Lexmark 2580+ Скачать руководство пользователя страница 120

Страница: 120 / 122

I-4

Service Manual

2580+, 2581+, 2590+, 2591+

Go Back

40X2979

Roller, upper feed (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X2980

Sub frame, right side

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X2981

Roller, lower feed (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X2984

Roller, ASF pick-up left and right (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-13

40X2985

Roller, ASF pick-up left and right (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-13

40X2986

Gear, ribbon drive rack (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-9

40X2987

Gear, ribbon drive rack (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-9

40X2988

Shaft, carrier (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X2989

Shaft, carrier (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X2992

Cover assembly, front unit (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X2993

Cover assembly, front unit (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X2994

Cover, front guide (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-5

40X2995

Cover, front guide (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-5

40X2996

Overlay pack, operator panel (258X)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-5

40X3001

Shaft set, tractor (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X3002

Tractor unit (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X3003

Tractor unit (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X3008

Plate, frame support (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-9

40X3013

Ribbon access cover unit (2580)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X3014

Ribbon access cover unit (2581)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X3019

Roller, lower pinch (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X3020

Roller, lower pinch (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X3021

Plate, carrier assembly (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-9

40X3022

Plate, carrier assembly (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-9

40X3023

Roller, ASF upper feed (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-13

40X3025

Ribbon access cover unit (2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X3026

Ribbon access cover unit (2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X3028

Narrow auto feeder assembly (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X3035

Wide dual tractor assembly (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X3136

ASF gears and bushings, parts packet

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-13

40X3141

Power cord—Austria, Belgium, Brazil, Germany, Greece, Finland, France, Indonesia, Luxembourg, Portugal,

Norway, Saudi Arabia (HV), Spain, Sweden, Netherlands, Turkey

- - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X4791

LAN card (INA)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-11

40X4968

INA support frame

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-11

40X4970

Earth LAN card

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-11

40X5006

INA cable

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-11

40X7978

Cover, top (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X7979

Cover, top (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X7980

Cover, bottom (2581, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X7982

Operator panel assembly (258X)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X7983

Operator panel assembly (259X)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X7984

Cable, operator panel

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-5

40X7985

Printhead assembly (2580, 2581)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X7986

Printhead assembly (2590, 2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X7987

Carrier unit (2580/2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X7988

Carrier unit (2581/2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X7991

Cable, printhead (2580)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X7992

Cable, printhead (2581)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X7993

Cable, printhead (2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X7994

Cable, printhead (2591)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-7

40X7995

Sensor, pull tractor and paper select

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-9

40X7997

Sensor, head gap and home position

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-9

40X7998

Sensor, top-of-form and paper present

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-9

40X8008

Motor, paper feed (with BKT)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-9

40X8010

Motor, carrier (with BKT)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-9

40X8011

Power supply unit

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-11

40X8014

Carrier fan

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-9

40X8032

Cover, bottom (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-3

40X8069

Cable, power supply (2580, 2590)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7-11

Содержание 2580+



























































































































Результаты поиска

Содержание 2580+

Отзывы:

Похожие инструкции для 2580+

Бренды по названию

Популярные бренды

Lexmark 2580+, Руководство по обслуживанию

Результаты поиска

Содержание 2580+

Отзывы:

Похожие инструкции для 2580+

Бренды по названию

Популярные бренды