Lexmark 2580+ Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 122

background image

Edition: April 3, 2012

The following paragraph does not apply to any country where such provisions are inconsistent with local law

:

LEXMARK INTERNATIONAL, INC. PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or
implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the
information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the
programs described may be made at any time.

Comments may be addressed to Lexmark International, Inc., Department D22X/002-1, 740 West New Circle Road,
Lexington, Kentucky 40550, U.S.A or e-mail at [email protected]. Lexmark may use or distribute any
of the information you supply in any way it believes appropriate without incurring any obligation to you.

References in this publication to products, programs, or services do not imply that the manufacturer intends to make these
available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or
imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that
does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in
conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the
user’s responsibility.

Lexmark, and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States
and/or other countries.

Optra Forms and PrintCryption are trademarks of Lexmark International, Inc.

PCL® is a registered trademark of the Hewlett-Packard Company.

All other trademarks are the property of their respective owners.

© 2011 Lexmark International, Inc.

All rights reserved.

UNITED STATES GOVERNMENT RIGHTS

This software and any accompanying documentation provided under this agreement are commercial computer software
and documentation developed exclusively at private expense.

P/N 12G9774

2580+, 2581+, 2590+, 2591+

«
1
2
3
4
...
»

Содержание 2580+



























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2580+

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 858

Бренд: B9Creations Страницы: 25

Бренд: Oki Страницы: 17

Бренд: Oki Страницы: 12

Бренд: Oki Страницы: 30

Бренд: Oki Страницы: 391

Бренд: Oki Страницы: 2

Бренд: Tally Страницы: 202

Бренд: Magicard Страницы: 30

Бренд: Magicard Страницы: 35

MAGICARD ID Card Printer

Бренд: Magicard Страницы: 30

Бренд: Magicard Страницы: 6

Бренд: Valentin Страницы: 96

Бренд: Olivetti Страницы: 78

Бренд: Citizen Страницы: 133

mobile pro advance

Бренд: AM TECH Страницы: 16

Aficio SP C730DN

Бренд: Ricoh Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды