Lexmark 2580+ Скачать руководство пользователя страница 95

Страница: 95 / 122

Preventive maintenance

6-1

2580+, 2581+, 2590+, 2591+

Go Back

6. Preventive maintenance

This chapter describes procedures for printer preventive maintenance. Follow these recommendations to help
prevent problems and maintain optimum performance.

Lubrication

Warning:

Petroleum-based lubricants can attack polycarbonate parts, causing premature failure. Use only

mineral oil-based lubricants.

•

The following parts should be lubricated when replaced:

•

Oil felt (carrier block)

•

Tractor unit

•

Side frame (left)

•

Side frame (right)

•

Pinch roller (lower)

•

Pinch roller spring (left)

•

Pinch roller spring (center)

•

Pinch roller spring (right)

•

Paper separator

Specified lubricants

•

Oil—P/N 1280443

•

Approved equivalents:

–

Mobil DTE27

–

Shell Tellus 100

–

Fuchs Renolin MR30

•

Grease—P/N 6934659

•

Approved equivalent: Mobil 28

Lubrication points

Oil

Lubricate the following contact positions:

•

Oil felt (carrier block)

•

Tractor shaft

Grease

Lubricate the following contact positions:

•

Side frame (left) and gears

•

Side frame (right) and ASF gears

•

Pinch roller, pinch roller springs, and paper separator

•

ASF side frames, gears, and combination lock mechanism

•

ASF side frame (left) and upper feed roll shaft

•

ASF pick-up roller shaft and roller bushings

Содержание 2580+



























































































































Результаты поиска

Содержание 2580+

Отзывы:

Похожие инструкции для 2580+

Бренды по названию

Популярные бренды

Lexmark 2580+, Руководство по обслуживанию

Результаты поиска

Содержание 2580+

Отзывы:

Похожие инструкции для 2580+

Бренды по названию

Популярные бренды