Leuze 50113704 Скачать руководство пользователя страница 58

Страница: 58 / 100

EtherCAT interface

Leuze electronic GmbH + Co. KG

AMS 338

TNT

35/7-2

Note!
Each device with Ethernet interface is uniquely identified via the MAC address assigned dur

ing production. The MAC address is also listed on the name plate of the device. If multiple

devices are commissioned in a system, the MAC address of each installed device must be

correctly assigned, e.g., during programming of the control.



Remove the "Address Link Label" from the device.



If necessary, add the IP address and the device name to the "Address Link Label".



Affix the "Address Link Label" in the documents, e.g., in the installation diagram, according

to the position of the device

9.4

EtherCAT – Cable lengths and shielding



Observe the following maximum cable lengths and shielding types:

Table 9.1:

Cable lengths and shielding

Connection

Interface

Max. cable length

Shielding

AMS – host

EtherCAT

100 m

Absolutely required

Network from

the first AMS to

the last AMS

EtherCAT

The maximum segment

length must not exceed

100 m for 100Base-TX

Twisted Pair (min. Cat. 5)

Absolutely required

Содержание 50113704





































































































Результаты поиска

Содержание 50113704

Отзывы:

Похожие инструкции для 50113704

Бренды по названию

Популярные бренды

Leuze 50113704, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50113704

Отзывы:

Похожие инструкции для 50113704

Бренды по названию

Популярные бренды