Leuze 50113704 Скачать руководство пользователя страница 48

Страница: 48 / 100

Display and control panel AMS 338i

Leuze electronic GmbH + Co. KG

AMS 338

TNT

35/7-2

8.3

Menu description

8.3.1

The main menus

After voltage has been applied to the laser, device information is displayed for several

seconds. The display then shows the measurement window with all status information.

AMS 338i 120

Leuze electronic

GmbH & Co. KG

SW: V 1.3.0 HW:1

SN: ---------------

Device information - main menu

This menu item contains detailed information on

• Device type

• Manufacturer

• Software and hardware version

• Serial number

No entries can be made via the display.

Network information

Address:

Alias:

Status:

INIT, PRE, SAFE, O

Network information - main menu

• Explanations of address, alias, status.

No entries can be made via the display.

IO1 LSR PLB

ECAT

IO2 TMP ATT

ERR

+ 87.000m

Status and measurement data - main menu

• Display of status, warning and error messages.

• Status overview of the switching inputs/outputs

• Bar graph for the received signal level.

• Link

• Measurement value

No entries can be made via the display.

See "Indicators in the display" on page 40..

Parameter

Parameter handling

EtherCAT

Position value

I/O

Other

Parameter - main menu

• Configuration of the AMS.

See "Parameter menu" on page 46.

Language selection

o Deutsch

o English

o Español

o Français

o Italiano

Language selection - main menu

• Selection of the display language.

See "Language selection menu" on page 50.

Service

Status messages

Diagnosis

Expanded diagnosis

Service - main menu

• Display of status messages.

• Display of diagnostic data.

No entries can be made via the display.

See "Service menu" on page 50.

Содержание 50113704





































































































Результаты поиска

Содержание 50113704

Отзывы:

Похожие инструкции для 50113704

Бренды по названию

Популярные бренды

Leuze 50113704, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50113704

Отзывы:

Похожие инструкции для 50113704

Бренды по названию

Популярные бренды