Leuze 50113704 Скачать руководство пользователя страница 49

Страница: 49 / 100

Display and control panel AMS 338i

AMS 338

Leuze electronic GmbH + Co. KG

Note!
The rear cover of this manual includes a fold-out page with the complete menu structure. It

describes the menu items in brief.

8.3.2

Parameter menu

Parameter handling submenu

The following functions can be called up in the

Parameter handling

submenu:

• Lock and enable parameter entry
• Set up a password
• Reset the AMS 338

to the default settings

Additional important information on parameter handling can be found at the end of the

chapter.

EtherCAT submenu

Note regarding the second station address - in short SSA- (formerly station alias)
The SSA is a freely configurable position-independent address which is often used for the

so-called hot connect. The values range from 0 to 65535. The SSA is persistently stored on

the AMS 338

and is available after the next start-up. A second option is to write the SSA to

Table 8.1:

Parameter handling submenu

Level 3

Level 4

Level 5

Selection/configuration option

Description

Standard

Parameter

enable

ON/OFF

The standard setting (

OFF

) prevents unintended parameter

changes.

With parameter enable activated (

), the display is inverted.

In this state, it is possible to change parameters manually.

OFF

Password

Activate

password

ON/OFF

To enter a password, parameter enable must be activated.

If a password is assigned, changes to the AMS 338

can only

be made after the password is entered.

The master password 2301 overrides the individually set

password.

OFF

Password

entry

For setting a four-digit numerical password.

Parameters to

default

By pressing the enter button

after selecting

Parameters to default

, all parameters are reset to their standard

settings without any further security prompts.

In this case, English is selected as the display language.

Tabelle 8.2: EtherCAT submenu

Level 3

Level 4

Level 5

Selection/configuration option

Description

Standard

Activation

ON/OFF

Address

(station alias)

Configuration option 0 - 65535

Содержание 50113704





































































































Результаты поиска

Содержание 50113704

Отзывы:

Похожие инструкции для 50113704

Бренды по названию

Популярные бренды

Leuze 50113704, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50113704

Отзывы:

Похожие инструкции для 50113704

Бренды по названию

Популярные бренды