Lenovo ThinkStation P330 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 134

background image

b. Note the orientation of the new flex storage enclosure. Then, slide the flex storage enclosure into the

flex bay from the front of the chassis until it snaps into position.

Figure 45. Installing the new flex storage enclosure

c. Connect the signal cable and the power cable to the new flex storage enclosure.

Note:

Reconnect any cables removed from other supported devices.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 89.

Storage drive in the front-access storage enclosure

Attention:

Do not open your computer or attempt any repair before reading and understanding the

Appendix A “Important safety information” on page 97.

You can install or replace a storage drive in the front-access storage enclosure. The storage drive also can
be hot-swappable, which means that you can install or replace the drive without even turning off your
computer. Therefore, lock the enclosure cover to prevent the unexpected removal. The keys are attached at
the rear of the computer. Store the keys in a secure place.

The storage drive in the front-access storage enclosure is hot-swappable only when the following
requirements are met:

• The eSATA mode of the SATA 4 connector is enabled.

• The SATA cable of the front-access storage enclosure is connected to the SATA 4 connector on the

system board. To verify the cable connection, see “Preparing your computer” on page 24 for more
information.

• The operating system of your computer does not reside on the storage drive installed in the front-access

storage enclosure.

Attention:

If any of the above requirements are not met, do not install or replace the storage drive when the

computer is turned on. Otherwise, data on the storage drive might get damaged.

3.5-inch storage drive

To remove or install a 3.5-inch storage drive, do the following:

48

P330 User Guide

«
...
52
53
54
55
56
...
»

Содержание ThinkStation P330







































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkStation P330

Бренд: Safco Страницы: 2

Toughbook CF-47 Series

Бренд: Panasonic Страницы: 32

ToughBook CF-72 Series

Бренд: Panasonic Страницы: 4

Toughbook CF-18 Series

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 40

Бренд: Panasonic Страницы: 140

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 4

Toughbook CF-47 Series

Бренд: Panasonic Страницы: 16

StorageWorks 4300

Бренд: Compaq Страницы: 21

Бренд: Festo Страницы: 72

ECS-9671 GTX950

Бренд: Vecow Страницы: 111

Бренд: Vecow Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды