Lenovo ThinkStation P330 Скачать руководство пользователя страница 60

Страница: 60 / 134

a. Note the orientation of the connector on the new storage drive. Then, flex both sides of the adapter

and align the four pins

with the corresponding holes in the storage drive.

Note:

Do not touch the circuit board (if accessible) of the 2.5-inch storage drive.

Figure 56. Installing the storage drive into the adapter

b. Align the four tabs on the adapter with the corresponding notches

in the converter. Then, slide the

storage drive as shown until the tab

snaps into position. The adapter with the storage drive is

installed into the converter.

Figure 57. Installing the adapter into the converter

P330 User Guide

Содержание ThinkStation P330







































































































































Результаты поиска

Содержание ThinkStation P330

Отзывы:

Похожие инструкции для ThinkStation P330

Бренды по названию

Популярные бренды

Lenovo ThinkStation P330, Руководство пользователя

Результаты поиска

Содержание ThinkStation P330

Отзывы:

Похожие инструкции для ThinkStation P330

Бренды по названию

Популярные бренды