Lenovo ThinkStation P330 Скачать руководство пользователя страница 72

Страница: 72 / 134

a. Align the screw hole in the cover presence switch with the corresponding hole in the chassis. Then

install the screw to secure the cover presence switch to the chassis.

Figure 76. Installing the cover presence switch

b. Connect the cover presence switch cable to the cover presence switch connector on the system

board.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 89.

Power supply assembly

Attention:

Do not open your computer or attempt any repair before reading and understanding the

Appendix A “Important safety information” on page 97.

Although there are no moving parts in your computer after the power cord has been disconnected, the
following warnings are required for your safety.

CAUTION:

Keep fingers and other parts of your body away from hazardous, moving parts. If you suffer an injury,
seek medical care immediately.

DANGER

Disconnect all power cords from electrical outlets before removing the computer cover or any part
that has the above label attached.

P330 User Guide

Содержание ThinkStation P330







































































































































Результаты поиска

Содержание ThinkStation P330

Отзывы:

Похожие инструкции для ThinkStation P330

Бренды по названию

Популярные бренды

Lenovo ThinkStation P330, Руководство пользователя

Результаты поиска

Содержание ThinkStation P330

Отзывы:

Похожие инструкции для ThinkStation P330

Бренды по названию

Популярные бренды