Lenovo ThinkStation P330 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 134

Lenovo ThinkStation P330 Скачать руководство пользователя страница 45

b. Locate the hole in the plastic holder to install the retention latch. Align the pin

a

with the

corresponding hole

b

in the plastic holder. Then press the retention latch downward into the hole

until it snaps into position.

Figure 29. Installing the retention latch

c. Hold the new M.2 solid-state drive by its edges and ensure that the circuit board side is facing

upward. Align the contact edge of the new drive with the key in the corresponding slot. Then carefully
insert the new drive into the slot at an angle of about 20 degrees and pivot the new drive downward.
Insert the plug of the retention latch into the hole to secure the new drive.

Note:

Do not touch the circuit board of the M.2 solid-state drive.

Figure 30. Installing the M.2 solid-state drive

Hardware removal and installation

39

«
...
43
44
45
46
47
...
»

Содержание ThinkStation P330







































































































































Отзывы:

Нет отзывов