Lenovo 7Z70 Скачать руководство пользователя страница 23

Страница: 23 / 212

Table 2. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSPUN2019I

Sensor [SensorElementName] has transitioned to a less severe state
from critical.

Informational

FQXSPUN2020I

Sensor [SensorElementName] has deasserted the transition to non-
recoverable from a less severe state.

Informational

FQXSPUN2023I

Sensor [SensorElementName] has deasserted the transition to non-
recoverable.

Informational

FQXSPUN2050I

The RAID controller in PCI slot [arg1] is no longer in critical status.

Informational

FQXSPUN2057I

The RAID controller in PCI slot [arg1] has a battery now.

Informational

FQXSPUP0002I

A firmware or software change occurred on system
[ComputerSystemElementName].

Informational

FQXSPUP4001I

Flash of [arg1] from [arg2] succeeded for user [arg3] .

Informational

FQXSPUP4002I

Flash of [arg1] from [arg2] failed for user [arg3].

Informational

FQXSPUP4006I

Auto promote primary XCC to backup is [arg1] by user [arg2] from
[arg3] at IP address [arg4].

Informational

FQXSPWD0000I

Watchdog Timer expired for [WatchdogElementName].

Informational

FQXSPWD0001I

Reboot of system [ComputerSystemElementName] initiated by
watchdog [WatchdogElementName].

Informational

FQXSPWD0002I

Powering off system [ComputerSystemElementName] initiated by
watchdog [WatchdogElementName].

Informational

FQXSPWD0003I

Power cycle of system [ComputerSystemElementName] initiated by
watchdog [WatchdogElementName].

Informational

FQXSPWD0004I

Watchdog Timer interrupt occurred for [WatchdogElementName].

Informational

FQXSPBR4001I

Running the backup Management Controller [arg1] main application.

Warning

FQXSPCA0007J

Numeric sensor [NumericSensorElementName] going high (upper
non-critical) has asserted.

Warning

FQXSPDM4002I

Device [arg1] VPD is not valid.

Warning

FQXSPEA0001J

Sensor [SensorElementName] has transitioned from normal to non-
critical state.

Warning

FQXSPIO0014J

Bus [SensorElementName] is operating in a degraded state.

Warning

FQXSPMA0010J

[PhysicalMemoryElementName] on Subsystem
[MemoryElementName] Throttled.

Warning

FQXSPNM4010I

DHCP[[arg1]] failure, no IP address assigned.

Warning

FQXSPNM4032I

DHCPv6 failure, no IP address assigned.

Warning

FQXSPPP4009I

The measured power value exceeded the power cap value.

Warning

FQXSPPP4010I

The new minimum power cap value exceeded the power cap value.

Warning

FQXSPPU0002G

The Processor [ProcessorElementName] is operating in a Degraded
State.

Warning

FQXSPPW0003G

Failure predicted on [PowerSupplyElementName].

Warning

FQXSPPW0006I

[PowerSupplyElementName] has lost input.

Warning

Chapter 2

XClarity Controller events

Содержание 7Z70





















































































































































































































Результаты поиска

Содержание 7Z70

Отзывы:

Похожие инструкции для 7Z70

Бренды по названию

Популярные бренды

Lenovo 7Z70, Справочник

Результаты поиска

Содержание 7Z70

Отзывы:

Похожие инструкции для 7Z70

Бренды по названию

Популярные бренды