Lenovo 7Z70 Скачать руководство пользователя страница 172

Страница: 172 / 212

•

FQXSFPU0023I: Secure Boot Image Verification Failure has been cleared as no failure in this round

boot.

Severity: Info

User Action:

Information only; no action is required.

•

FQXSFPU0027N: System uncorrected recoverable error has occurred on Processor [arg1] Core

[arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6].

Severity: Fatal

User Action:

Waiting for update.

•

FQXSFPU0030N: A firmware fault has been detected in the UEFI image.

Severity: Error

User Action:

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this

error.

2. Reflash UEFI image.

3. Undo recent system changes (settings or devices added). Verify that the system boots. Then, re-

install options one at a time to locate the problem.

4. If problem persists, save customer's UEFI configurations, then remove and re-install CMOS battery

for 30 seconds to clear CMOS contents. If it boots successfully, then restore system settings.

5. If the problem persists, collect Service Data logs.

6. Contact Lenovo Support.

•

FQXSFPU0031N: The number of POST attempts has reached the value configured in F1 setup.The

system has booted with default UEFI settings. User specified settings have been preserved and will
be used on subsequent boots unless modified before rebooting.

Severity: Error

User Action:

Complete the following steps:

1. Original UEFI settings are still present. If customer desires to continue using the original settings,

select Save Settings.

2. If User did not intentionally trigger the reboots, check logs for probable cause. For example, if there

is a battery fault event, follow the steps to resolve that event.

3. Undo recent system changes (settings or devices added). Verify that the system boots. Then, re-

install options one at a time to locate the problem.

4. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this

error. Update UEFI firmware if applicable.

5. Save customer's UEFI configurations, then remove and re-install CMOS battery for 30 seconds to

clear CMOS contents. If it boots successfully, then restore system settings.

6. If the problem persists, collect Service Data logs.

7. Contact Lenovo Support.

•

FQXSFPU0033G: Processor has been disabled.

168

ThinkSystem SR630 V2 Messages and Codes Reference

Содержание 7Z70





















































































































































































































Результаты поиска

Содержание 7Z70

Отзывы:

Похожие инструкции для 7Z70

Бренды по названию

Популярные бренды

Lenovo 7Z70, Справочник

Результаты поиска

Содержание 7Z70

Отзывы:

Похожие инструкции для 7Z70

Бренды по названию

Популярные бренды