Lenovo 7Z70 Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 212

background image

Table 3. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSFPU4060I

Skipped freezing lock of AHCI-attached SATA drives.

Informational

FQXSFPU4061I

Restored default locking behavior of AHCI-attached SATA drives.

Informational

FQXSFPU4080I

Host Power-On password has been changed.

Informational

FQXSFPU4081I

Host Power-On password has been cleared.

Informational

FQXSFPU4082I

Host Admin password has been changed.

Informational

FQXSFPU4083I

Host Admin password has been cleared.

Informational

FQXSFPU4084I

Host boot order has been changed.

Informational

FQXSFPU4085I

Host WOL boot order has been changed.

Informational

FQXSFSM0007I

The XCC System Event log (SEL) is full.

Informational

FQXSFSR0002I

[arg1] GPT corruption recovered, DiskGUID: [arg2]

Informational

FQXSFDD0001G

DRIVER HEALTH PROTOCOL: Missing Configuration. Requires
Change Settings From F1.

Warning

FQXSFDD0002M

DRIVER HEALTH PROTOCOL: Reports 'Failed' Status Controller.

Warning

FQXSFDD0003I

DRIVER HEALTH PROTOCOL: Reports 'Reboot' Required Controller.

Warning

FQXSFDD0005M

DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires
'Reboot'.

Warning

FQXSFDD0006M

DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver.

Warning

FQXSFDD0007G

Security Key Lifecycle Manager (SKLM) IPMI Error.

Warning

FQXSFIO0008M

An intra-board UPI dynamic link width reduction has been detected
on the link between processor [arg1] port [arg2] and processor [arg3]
port [arg4].

Warning

FQXSFIO0009M

An inter-board UPI dynamic link width reduction has been detected
on the link between processor [arg1] port [arg2] and processor [arg3]
port [arg4].

Warning

FQXSFIO0013I

The device found at Bus [arg1] Device [arg2] Function [arg3] could not
be configured due to resource constraints. The Vendor ID for the
device is [arg4] and the Device ID is [arg5]. The physical slot number
is [arg6].

Warning

FQXSFIO0016M

IFM: Reset loop avoided - Multiple resets not allowed.

Warning

FQXSFIO0021J

PCIe Error Recovery has occurred in physical [arg1] number [arg2].
The [arg3] may not operate correctly.

Warning

FQXSFIO0022J

PCIe Link Width has degraded from [arg1] to [arg2] in physical [arg3]
number [arg4].

Warning

FQXSFIO0023J

PCIe Link Speed has degraded from [arg1] to [arg2] in physical [arg3]
number [arg4].

Warning

FQXSFIO0032M

PCIe Correctable Error PFA Threshold limit has been exceeded at Bus
[arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is
[arg4] and the Device ID is [arg5]. The physical bay number is [arg6].

Warning

FQXSFIO0033J

PCIe Link Width has degraded from [arg1] to [arg2] in physical bay
number [arg3].

Warning

.

137

«
...
139
140
141
142
143
...
»

Содержание 7Z70





















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7Z70

Бренд: Kathrein Страницы: 16

Бренд: ExtraHop Страницы: 5

Vlinx Serial Servers ESP901E

Бренд: B&B Electronics Страницы: 92

Бренд: AIC Страницы: 112

Бренд: AC&T System Страницы: 32

Бренд: IBM Страницы: 96

Бренд: MO-SYS Страницы: 26

Бренд: Hitachi Страницы: 57

Бренд: Hitachi Страницы: 76

BladeSymphony 1000

Бренд: Hitachi Страницы: 52

Бренд: Hitachi Страницы: 91

Бренд: Hitachi Страницы: 174

HVM Navigator V03-06

Бренд: Hitachi Страницы: 312

NVM Navigator v03-07

Бренд: Hitachi Страницы: 316

Бренд: Hitachi Страницы: 129

Бренд: Hitachi Страницы: 466

Бренд: Hitachi Страницы: 530

VisionBase 8880R

Бренд: Hitachi Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды