Lafayette Parasol Accu-Rise Скачать руководство пользователя страница 44

Страница: 44 / 83

Parasol Installation Instructions

BACK

REMOVE THE SHADE

Standard Brackets

- Fully raise the shade.
- While holding the headrail, loosen the tab screw on

each bracket to release the headrail.

Swivel Brackets

- Fully raise the shade.
- While holding the headrail, pull the push tab to rotate

the swivel arm to the open position to release the

headrail.

End Mount Brackets

- Reverse the installation procedures.

Tab

CARE AND CLEANING

Regular light dusting with a feather duster is all the

cleaning that is needed in most circumstances. For

deeper cleaning, vacuum gently with a soft brush

attachment. Do not vacuum Triple cell fabrics.

LEVEL THE BOTTOM RAIL (IF NECESSARY)

If the bottomrail or the middle moving rail of a

top-down/bottom-up shade is not level, it can be adjusted

by following the procedure:
   - Remove the right end cap from the rail that is not level.
  - Pull out the section labeled TOOL.
  - Push in on the adjustment screw with the tool and turn

to adjust rail. Turning clockwise will move the rail down,

counterclockwise will move the rail up.
Note: The middle rail may need to be raised or lowered

slightly to allow the adjustment screw to be pushed in.

When the rail is level, replace the tool and the endcap.

18-67IN-40 May 2018

Содержание Parasol Accu-Rise




















































































Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды

Lafayette Parasol Accu-Rise, Руководство по установке

Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды