Lafayette Parasol Accu-Rise Скачать руководство пользователя страница 9

Страница: 9 / 83

Parasol Installation Instructions

BACK

CARE AND CLEANING

Regular light dusting with a feather duster is all the

cleaning that is needed in most circumstances. For

deeper cleaning, vacuum gently with a soft brush

attachment. Do not vacuum Triple cell fabrics.

INSTALL CORD TENSION LOCK

The revised American National Standard

for Safety of Corded Window Covering

products requires if corded window

products are used in the home, cord

cleats or cord tension locks must be

properly installed.
- See separate instructions included for installation of

the Cord Tension Lock for child and pet safely.

INSTALL OPTIONAL HOLD-DOWNS

Lower the shade and place the pins from the

hold-down brackets into the end caps on the

bottom rail.
- On the mounting surface, mark the bracket

hole locations.
- Check that the brackets are level and attach them to

the mounting surface using two screws.

REMOVE THE SHADE

Standard Installation Brackets - (A.)

- Fully raise the shade.
- Loosen the tab screw on each installation bracket to

headrail. Note: For non-operable shades, gently pull

fabric away from window and loosen the tab screw to

release the headrail.

Swivel Installation Brackets - (B.)

- Fully raise the shade.
- Pull the tab to rotate the swivel arm to open position and

release the headrail.

Rectangular Shade - (C.)

- Lower the shade approximately 4”.
- While holding the headrail, push back on the bottom tab

of the installation bracket to release the bottom edge of

the headrail.
- After releasing the bottom edge, roll the back of the

headrail down and out from the bracket.

Bottom

Tab

Back of

Shade

Headrail

Bracket

Tab

Содержание Parasol Accu-Rise




















































































Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды

Lafayette Parasol Accu-Rise, Руководство по установке

Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды