Lafayette Parasol Accu-Rise Скачать руководство пользователя страница 75

Страница: 75 / 83

Parasol Installation Instructions

BACK

INSTALL THE BRACKETS Cont.

End Mount

- Position the end mount brackets so that the top of the

attached installation brackets equal the ordered height

of the shade. Mounting surface must be vertical and

flat.

- Mount brackets using the screws provided. Drywall

mounting is not recommended.

INSTALL THE SHADE

- Fit the front channel on top of the headrail onto the front

lip of the installation brackets.

- Push the headrail up and back until it snaps into the

brackets.

- Check to ensure the headrail is securely in the brackets.

Minimum

Ordered

Shade

Height

Ordered

Shade Height

The back of the headrail

snaps into the bracket.

The front of the bracket

fits under the groove.

Headrail

Bracket

Snap

in Place

INSTALL OPTIONAL HOLD-DOWNS

Lower the shade and place the pins from the hold-down

brackets into the end caps on the bottom rail.
- On the mounting surface, mark the bracket hole

locations.
- Check that the brackets are level and attach them to

the mounting surface using two screws.

End Mount

LEVEL THE BOTTOM RAIL (If Necessary)

- Lift the bottom rail to locate the pockets on the

underside of the rail.
- Gently pull down on the bottom rail to fully insert the

7/64” allen wrench key into the pocket. The key is fully

inserted when the ring on the key abuts to the pocket.
- Lift up on the bottom rail slightly before turning the Allen

wrench key. Turn the key clockwise to raise that side of

the bottom rail, or counter-clockwise to lower it.
- One quarter turn of the key equals approximately 1/4”.

- Adjust the end pockets first. Then adjust any additional

pockets as necessary to maintain equal tension across

the bottom rail.

Pocket

Underside of Bottom Rail

Allen

Wrench

Key

Lower

Raise

Содержание Parasol Accu-Rise




















































































Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды

Lafayette Parasol Accu-Rise, Руководство по установке

Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды