Lafayette Parasol Accu-Rise Скачать руководство пользователя страница 12

Страница: 12 / 83

Parasol Installation Instructions

INSTALL THE BRACKETS - STAND-ALONE ARCH

Outside Mount (A.)

- Center the arch over the window opening at the

desired height and lightly mark each end on a flat

    mounting surface.
  - Mark 3” from each end of the headrail.
  - Center the installation brackets or extension brackets

on your marks and

mount level and flush against a flat

mounting surface using the screws provided. Use

drywall anchors if necessary.

Inside Mount (B.)

- Measure 3” from each jamb for bracket location. If more

than two brackets came with your order, space

additional brackets evenly between the two and mark

their location.

- Center and mount the brackets on your marks with the

longer side of the bracket against the mounting surface

and the tab screw or shorter side facing up.

End Mount (C.)

- Slightly remove the end caps from the bottom rail. Do

not remove them all the way.

- Insert the short end of the specialty end mount bracket

under each of the end caps and into the small fabric

channels on the bottom of the rail.

INSTALL THE BRACKETS - ARCH SHARING HEADRAIL

- Refer to the “End Mount” section in the installation

instructions that came with your rectangular shade.

3/8”

Installation

Bracket

3/4”

Installation

Bracket

1 1/4”

Installation

Bracket

3/8”

Swivel

Bracket

3/4”

Swivel

Bracket

3/8”

End Mount

Bracket

3/4”

End Mount

Bracket

Additional Installation Bracket

Swivel Bracket (

Swivel Eyelet

Mark screw locations.

Additional Installation Bracket

End Mount

Bracket

Rail

End Cap

Small Fabric Channels

Long

End

Short

End

(

" pleat similar)

" Pleat Rail

Specialty End

Mount Bracket

INSTALL THE STAND-ALONE ARCH

Standard Installation Brackets (D.)

- Loosen the tab screw on each bracket.
- Push the rail into the brackets. Make sure fabric is not

caught between the tab and the rail.
- Tighten the tab screw on each bracket. Do not

overtighten. If necessary, gently move the fabric

forward to access the screw.

Swivel Installation Brackets (E.)

- Position the moveable tab outward on each bracket.

- With the front side of the fabric facing you, lift the shade

into position so the rail is against the back of the

brackets.
- Rotate the moveable tabs against the rail to lock into

place. Make sure the shade is tightly secrued.

Tab Screw

Headrail

Front

Bracket Open

Bracket Locked

Locking

Tab

Screw Holes

Push

Tab

Locking Tab

Содержание Parasol Accu-Rise




















































































Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды

Lafayette Parasol Accu-Rise, Руководство по установке

Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды