Lafayette Parasol Accu-Rise Скачать руководство пользователя страница 78

Страница: 78 / 83

Parasol Installation Instructions

BACK

Cellular Window Shades

System II Installation Instructions

Thank you for choosing Parasol Cellular Shades. With proper installation and care,

your new shades will provide many years of beauty and performance.

Mounting Surface

Fastener

Wood

Drywall, Plaster

Metal

#6 Hex Head

Provided

Wall Anchors

Not Provided

Sheet Metal

Not Provided

Tools Needed

Power Drill, 1/4” Driver and drill bits

Tape Measure

Flat blade Screwdriver

Phillips Screwdriver

Pencil

Level

Installation

Brackets

Spacer

Blocks

INSTALL THE BRACKETS

Outside Mount

- Center the headrail over the window opening at the

desired height and lightly mark each end on a flat

    mounting surface.
  - Mark 2” from each end of the headrail.
  - If more than 2 brackets came with order, space

additional brackets evenly between and mark their

location.

- Caution:

When using high mount battery bracket

(standard), you will need 18 1/4” between the 2

brackets nearest to motor side. If using low mount,

use standard spacing.

If NOT using high mount battery bracket, remove spacer

block from shade bracket.
- Center the installation brackets or extension brackets

on your marks and mount flush against the mounting

surface using the screws provided. Use drywall anchors

if necessary.

Shade Width

12” - 36”

36 1/16” - 72”

72 1/16” - 108”

108 1/16” - 120”

Brackets Required

3/8” & 3/4”

Installation

Bracket

3/8” & 3/4”

End Mount

Brackets

Outside Mount

Содержание Parasol Accu-Rise




















































































Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды

Lafayette Parasol Accu-Rise, Руководство по установке

Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды