Lafayette Parasol Accu-Rise Скачать руководство пользователя страница 52

Страница: 52 / 83

Parasol Installation Instructions

BACK

REMOVE THE SHADE

Standard Brackets

- Fully raise the shade.
- While holding the headrail, loosen the tab screw on

each bracket to release the headrail.
- Outside mount: Loosen the tab screw on each bracket

to release the anchor rail.
- Inside mount: Loosen the screw in the anchor rail.

CARE AND CLEANING

Regular light dusting with a feather duster is all the

cleaning that is needed in most circumstances. For

deeper cleaning, vacuum gently with a soft brush

attachment. Do not vacuum Triple cell fabrics.

18-67IN-16 March 2017

Troubleshooting

Problem

The shade will not fit into the installation brackets.

Solution

Check that the installation brackets are level and aligned. Shim the installation brackets to level the

headrail, if necessary.

Be sure the heads of the screws are flush against the installation bracket.

Check that the headrail is completely inserted into the installation brackets.

See “Install the Shade”

Problem

The shade is hard to raise or lower, or will not raise or lower.

Solution

Make sure that the shade fabric is not caught between the installation bracket and the headrail.
Check that the headrail and installation brackets are level and aligned in the window. Shim the

installation brackets to level the headrail, if necessary.

Problem

The shade raises or lowers unevenly or the bottom rail is uneven when fully raised.

Solution

Check that the headrail and installation brackets are level and aligned. Shim the installation brackets

to level the headrail, if necessary.
Check to see if there is an obstruction in the shade’s path. If a shade hits an obstruction as it is

lowered it may become misaligned. This may cause the shade to be angled or tilted when fully

raised. Try lowering the shade completely, then raising it to allow it to self-correct.
Adjust the cord tension. See “Adjust the Shade”

Содержание Parasol Accu-Rise




















































































Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды

Lafayette Parasol Accu-Rise, Руководство по установке

Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды