KYOWA MRS-100 Series Скачать руководство пользователя страница 9

Страница: 9 / 81

IMPORTANT REGULATORY INFORMATION

The product is for use only in Japan, the United States, India, Thailand and the European Union.

Use in other countries or regions is prohibited.

JAPAN

Type certification

The product has been certified as a low-power data communications system in the 2.4 GHz band

(Technical Regulations Conformity Certification System: Ordinance of MPT No. 37, 1981, Article 2,

paragraph 1, item (19)) according to the Radio Law of Japan.

Accordingly, no radio equipment license is required to use this product. However, the following actions

may be punishable under law:

• Disassembling or modifying the product.
• Removing the certification label on the product.

Name of radio equipment: MR-2400M Number of type certification: 007-AE0235

FCC

COMPLIANCE WITH ELECTRIC DIRECTIVES & REGULATIONS

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

[CAUTION]

Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Contains Transmitter Module

FCC ID: 2AJE9, MR-2400MA

This device should be used EXCLUSIVELY as the digital devices for industrial, commercial or medical

test equipment. "Test equipment" includes devices used for maintenance, research, evaluation,

simulation and other analytical or scientific applications in areas such as industrial plants, public

utilities, hospitals, universities, laboratories, automotive service centers and electronic repair shops.

INDIA

REGULATORY NOTRICE FOR Radio Frequency module

•

Notice for users in India

The name of RF module: MR-2400MA

THAILAND

REGULATORY INFORMATION

in Thailand

NOTE

Содержание MRS-100 Series


















































































Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды

KYOWA MRS-100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды