KYOWA MRS-100 Series Скачать руководство пользователя страница 64

Страница: 64 / 81

7-5. Radio interference

This telemeter operates on the 2.4 GHz band.

If there are multiple other wireless systems, such as those using wireless LAN or Bluetooth

, or radio equipment

on the 2.4 GHz band in the same environment, the other radio equipment may cause radio jamming and result in

communication becoming unstable.

The following figure shows the frequency channels and radio frequency used for communication by this

telemeter and typical radio systems on the 2.4 GHz band. (Telemeter: MRS; wireless LAN and Bluetooth

)

Normal radio communication can be interrupted if the transmitting and receiving radio frequency used by your

radio equipment and the telemeter overlaps. Switching to a frequency channel that will not affect the

transmission or reception of the telemeter may improve communication. Note that the telemeter is sensitive to

wireless LAN communication.

0ch

(2405MHz)

2ch

(2415MHz)

4ch

(2425MHz)

6ch

(2435MHz)

8ch

(2445MHz)

Ach

(2455MHz)

Cch

(2465MHz)

Ech

(2475MHz)

1ch

(2410MHz)

3ch

(2420MHz)

5ch

(2430MHz)

7ch

(2440MHz)

9ch

(2450MHz)

Bch

(2460MHz)

Dch

(2470MHz)

Fch

(2480MHz)

*BW=22MHz

2400MHz

2410MHz

2420MHz

2430MHz

2440MHz

2450MHz

2460MHz

2470MHz

2480MHz

2490MHz

2500MHz

1ch (2412MHz)

2ch (2417MHz)

3ch (2422MHz)

4ch (2427MHz)

5ch (2432MHz)

6ch (2437MHz)

7ch (2442MHz)

8ch (2447MHz)

9ch (2452MHz)

10ch (2457MHz)

11ch (2462MHz)

12ch (2467MHz)

13ch (2472MHz)

14ch (2484MHz)

Bluetooth: 2402 - 2480MHz (2402+kMHz, k=0, 1, 2,

, 78)

MRS:

wireless LAN:

Содержание MRS-100 Series


















































































Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды

KYOWA MRS-100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды