KYOWA MRS-100 Series Скачать руководство пользователя страница 63

Страница: 63 / 81

7-4. OPTIONAL ACCESSORIES

The following optional accessories is available for the telemeter:

E-03* [Extension cable for receiving antenna (6 m)]

The extension cable can provide an even longer extension for the receiver’s receiving antenna.

The external diameter of the cable is 2.7 mm, which is the same as that of the included extension cable for the

receiving antenna (2 m).

*E-03 cannot be used in Europe.

EXT-ANT1 [Small planar antenna]

This is effective when the receiving antenna must be installed in a narrow space.

EXT-ANT2 [Planar diversity antenna]

This single antenna has two orthogonal polarizations—vertical polarization (V-pol.) and horizontal polarization

(H-pol.)—that enable reception even if the polarization changes.

AC power supply cables

The AC power supply cables are supported in the countries and regions indicated below. Use the one for your

country or region. P-38 (Japan), P-39 (USA), P-40 (India), P-41 (Europe), P-42 (Thailand)

Φ3.2

27.

19.5

Planes of polarized waves

in two directions

• Connected to "MAIN" and "SUB" on the

receiver, respectively.

• Can be connected to the antenna extension cable.

14.7

Содержание MRS-100 Series


















































































Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды

KYOWA MRS-100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды