KYOWA MRS-100 Series Скачать руководство пользователя страница 55

Страница: 55 / 81

The telemeter uses the 2.4 GHz band radio frequency.

Radio waves in this frequency band have high straightness, so the waves are less likely able to maneuver

around obstacles. For this reason, install the transmitting and receiving antennas so that each antenna is

visible from the position of the other. In addition, if the transmitter or receiver is installed in a place that

moves, ensure that the transmitting and receiving antennas are mutually visible throughout the path of

movement.

Avoid installing the antennas near the floor, the ground plane, and/or metal surfaces.

The antenna properties might worsen when the transmitting and receiving antennas are installed near the floor,

the ground plane, and/or metal surfaces. Thus, to the extent possible, install the transmitting and receiving

antennas away from those areas.



Installation precautions for the transmitters

In case of MRS-104A-S

In case of MRS-101A-S/V



Installation precautions for the receiving antenna (In case

of the High gain dipole antenna

DA-DB-05RP-SMA-08)

In case of the high gain dipole antenna

（

DA-DB-05RP-SMA-08

）

Metal wall

Metal surface

As far away

as possible

Metal wall

Metal surface

As far away

as possible

Extension cable for receiving antenna

As far away

as possible

Floor, ground plane,
Metal surface, etc.

Содержание MRS-100 Series


















































































Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды

KYOWA MRS-100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды