KYOWA MRS-100 Series Скачать руководство пользователя страница 33

Страница: 33 / 81

●If using the MRS-101A-V (1ch-Voltage Transmitter)

Pin Assignment

Pin No.

Signal Name

* Not used

-IN

(-) side input

* Not used

+IN

(+) side input

SHIELD

Shield

Avoid using a power supply with the wrong polarity, as it may damage the product.

Wire the devices so as to avoid disconnection if the transmitter, strain gage, battery, or respective wiring is twisted or

vibrates.

If using the SHIELD (E) terminal with the MRS-101A-V, caution is required.

For details, see "MRS-101A-V (1ch-Voltage Transmitter)_READ IN THE BEGINNING."

NOTE

The Adapter can be removed for replacement. To reconnect it, solder the pins on the Adapter.

Avoid exposing the Adapter to excessive solder and heat from the soldering iron.

NOTE

Keep the sensor wire short. Long wiring may introduce noise into sensor signals and negatively affect

signal transmission and reception.

Keep the battery wire short. Long wiring may negatively affect signal transmission and reception.

The included battery holder, which houses two AAA-cell batteries, is not designed to withstand vibration,

impact, or centrifugal force. Use the batteries in the holder only for checking operation.

NOTE

Recommended battery

･

Lithium (CR2)

･

Ni-MH (AAA cell×2)

･

Alkaline (AAA cell×2)

⊕

⊖

Device under test

“

Voltage output type ransducer”,etc.

Voltage adapter

ADP-03

Содержание MRS-100 Series


















































































Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды

KYOWA MRS-100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды