KYOWA MRS-100 Series Скачать руководство пользователя страница 66

Страница: 66 / 81

8. SPECIFICATIONS

8-1. MRS-114A

■

Hardware Specifications

Number of Output Channels

Analog Output Accuracy

Within ±0.1%FS

DA Resolution

16 bits

DA Conversion Speed per channel

1 measurement channel at 4.8 kHz

2 measurement channels at 3.2 kHz

3 measurement channels at 2.4 kHz

4 measurement channels at 1.92 kHz

Operating Temperature, Humidity

0 to 50 °C, 20 to 85 % (Non condensing).

Vibration Resistance

29.42 m/s

(3G), 5 to 200 Hz

Shock Resistance

294.2 m/s

(30G), 11 ms

Power Supply

10 to 16VDC

Current Consumption

Within 280 mA

Operating Switch

MUTE: Turn buzzer on/off.

BAL: Execute balance adjustment.

CHECK: Check sensor connection.

START: Start measurement.

STOP: Stop measurement.

Tx OFF: Turn transmitter off.

SLEEP: Set transmitter to sleep. Wake-up after the set time.

Indicator

Monitor transmitter battery in 3 steps.

Monitor Received Signal Strength in 3 steps.

7-segment LED: Indicate a frequency channel (0 to F)

DATA: Light up in response to radio communication error /non- error.

Lock: Light up to indicate keys are locked.

Dimensions

210 (W) × 35 (H) × 157.5 (D) mm (Excluding protrusions)

Weight

Approx. 600 g

Compliance

Directive 2014/53/EU (RED)

Directive 2011/65/EU (6 restricted substances) (RoHS)

Содержание MRS-100 Series


















































































Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды

KYOWA MRS-100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание MRS-100 Series

Отзывы:

Похожие инструкции для MRS-100 Series

Бренды по названию

Популярные бренды