Battery Charge
When charging the battery with the battery
charger, follow the correct steps according to
the handling instructions attached to the
battery charger.
Danger
Danger
Do not connect the charge clip to the battery
nor remove it while the power of the battery
charger is ON.
Failure to observe these precautions could
cause a fire or an explosion.
If the battery charger has a changeover switch
for voltage, set the battery voltage for charge.
If the voltage for charge is wrong, it may
cause overheating or ignition of the battery
charger or explosion of the battery.
Warning
Charging the battery mounted on the vehicle
may cause ignition, explosion, or damage on
the vehicle or equipment.
If there is no way other than to charge the
battery mounted on the vehicle, remove the
minus cable terminal on the vehicle side,
which is connected to the battery.
When connecting to the battery charger, firmly
connect the plus and minus charge clip to the
plus and minus terminals of the battery,
respectively.
If they are connected reversely or loosely, it
may cause ignition, explosion, failure of the
battery charger, or damage on the vehicle or
equipment due to the polarity inversion of the
battery.
Set the charging current to 1/10 or less than
the rating capacity of battery. In the case of
fast charging, set it to that rating capacity or
less.
If the charging current is too high, it may
cause ignition or explosion due to electrolyte
leaks or liquid shortage.
Do not mount the battery on the vehicle
immediately and wait for 30 minutes after
charging.
Failure to observe these precautions could
cause a fire or an explosion.
Caution
The temperature of the electrolyte must be
45°C or lower during charging. In the case of
fast charging, it must be 55°C or lower.
If the temperature exceeds these limits, it
could result in battery deformation or
electrolyte leaks.
When charging the battery, remove the vent
plug of the battery, if possible, to expedite the
diffusion of the hydrogen gas derived from the
battery.
Electrolytic solution adheres to the vent plug,
so be careful so that your skin nor clothes do
not touch the solution.
If the electrolyte level is lower than halfway
between the solution levels, add purified water
up to the UPPER LEVEL (maximum line).
If UPPER LEVEL is exceeded, it may cause
electrolyte leaks.
If the battery gets extremely hot or releases a
significant amount of gas during charging,
disconnect the battery charger power plug
immediately.
Important
Fast charging is not suitable for charging to
recover the battery left for a long time.
A high electrolyte temperature deteriorates
parts such as polar plates inside the battery
and shorten its lifetime.
Follow this procedure to fully charge the
battery.
Use a taper battery charger, which
automatically reduces the charging rate
during charging.
After charging is completed, fill the battery
cells with distilled water. (if the battery is in
use).
After charging is completed, measure and
record the specific gravity of each cell using
a battery hydrometer.
Replace it when the specific gravity is 1.225
or less, or gap of that between each cell is
0.05 or more.
1.
2.
3.
4.
LM531
Electrical System
Page 5-6
General Inspection and Repair
Содержание Baroness LM531
