Kugelmann Maschinenbau DUPLEX Скачать руководство пользователя страница 51

Страница: 51 / 60

Chapter 05

www.kugelmann.com

If the screws cannot be moved this way, the spreading material may be frozen or the screw is blocked through a
foreign object. In this case the container has to be emptied with a shovel from above.

Under no circumstances remove the grid while the vehicle is in operation. Stop the motor

and de-couple the hydraulic pipes.

Operation by hand is only foreseen in emergencies. Repair the defective part immediately,

contact your dealer or an expert repair shop.

If there is danger for humans or equipment the equipment has to be stopped

immediately and the customer service be contacted.
STOP MOTOR AND REMOVE IGNITION KEY!!!

The operator has to take care that the vehicle combination is found in an operating and

roadworthy condition! Works which do not conform to regulations has to be refused!

Never work near the machine wearing loose clothing which can be caught in running

parts!

Make sure that during operati9n of the machine all protective measures are attached!

Subject to changes

English

Содержание DUPLEX





























































Результаты поиска

Содержание DUPLEX

Отзывы:

Похожие инструкции для DUPLEX

Бренды по названию

Популярные бренды

Kugelmann Maschinenbau DUPLEX, Руководство по эксплуатации

Результаты поиска

Содержание DUPLEX

Отзывы:

Похожие инструкции для DUPLEX

Бренды по названию

Популярные бренды