Kugelmann Maschinenbau DUPLEX Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 60

background image

Chapter 05

41

www.kugelmann.com

Starting the spreader

Before driving check all fixations again. Is the spreader mounted in the correct position? Are all bolts fixed and
properly secured?

Operation of the equipment, its care, repair and maintenance must always be dóne by

instructed personnel.

Never work near the machine wearing loos clothes which can be caught in running parts.

Do not work on the machine while it is running!

STOP MOTOR AND EMOVE IGNITION KEY!!!

After shutting down the equipment tool/part of machine can still run on.

The spreading disc unit can be changed from transport mode to working mode with a few moves.

Draw fixing bolt of the locking device lever on the left side, turn by 90 degrees and snap into place.

Fold locking device lever upwards or to the front while holding on to the spreader unit. Swing spreader unit
downwards. Draw locking bolt (left and right one each), move securing lever downwards with handle knob until
the locking bolt snaps into the lower oblong hole. Make sure that both security levers are secured with the
securing bolts.

Subject to changes

Englsih

«
...
39
40
41
42
43
...
»

Содержание DUPLEX





























































Отзывы:

Нет отзывов

Похожие инструкции для DUPLEX

Бренд: I-Rocks Страницы: 4

iCLASS SE Biometric Reader

Бренд: HID Страницы: 50

Бренд: Advanced Card Systems Страницы: 96

Бренд: Stanley Страницы: 48

Бренд: SureFlap Страницы: 6

Бренд: Datamars Страницы: 30

Бренд: Nordic ID Страницы: 12

Бренд: Nordic ID Страницы: 35

Бренд: Viking Страницы: 20

cyberJack RFID universal

Бренд: Reiner Страницы: 32

NetworX NX-1700E

Бренд: Interlogix Страницы: 18

Бренд: Kaba Страницы: 82

Бренд: LEHNER Страницы: 52

Бренд: SPYKER Страницы: 12

Бренд: SPYKER Страницы: 12

Бренд: Savi Страницы: 4

OBID i-scan ID ISC.PRH110-A

Бренд: Feig Electronic Страницы: 24

Бренд: Panasonic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды