Kugelmann Maschinenbau DUPLEX Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 60

background image

54

Maintenance and care, wear parts

Maintenance and care

The mountable spreader of the company Kugelmann is for the most part maintenance free. The bearings of the
screw conveyors are at the front equipped with lubricating nipples. The chain tension (drive of the screw
conveyor) should be checked monthly and be corrected if needed. Per hydraulic motor 4 screws have to be
loosened, the hydraulic motor has to be positioned new and the screws to be tightened again.

These four screws are to be loosened and after tightening
the driving chain to be tightened again.

Spreader with electric spreading pattern adjustment

With spreaders equipped with electric spreading pattern adjustment (ESP), the piston rod has to be kept clean. It

moves the spreading disc forewards and backwards and thus has to be cleaned regularly.

Spreader with drive via p.t.o. hydraulic pump

After each work assigment the p.t.o hydraulic pump has to be checked for secure position so that it cannot turn.
The oil level can be checked at the inspection glass on the side. Fill gear oil SAE 80 or 90, about 0.5l up to
inspection glass height. Change gear oil, hydraulic oil and filter regularly.

Spreader with separate drive motor

Maintenance of motor according to producer specifications, see instruction. Disconnect battery in summer.

Spreader with damp salt equipment

After dismounting of spreader at the end of the season clean the brine tanks with clear water. Connect C-hose to

hydrant perhaps and rinse the tanks thoroughly.

At the end rinse brine pump with Glysantine. The pump can remain filled with Glysantine over the summer.

Subject to changes

English

«
...
52
53
54
55
56
...
»

Содержание DUPLEX





























































Отзывы:

Нет отзывов

Похожие инструкции для DUPLEX

Бренд: Hama Страницы: 16

Бренд: Kobil Страницы: 3

Бренд: IDTECK Страницы: 20

Бренд: IDTECH Страницы: 19

Бренд: IDTECH Страницы: 23

Бренд: IDENTEC SOLUTIONS Страницы: 55

Бренд: Sven Страницы: 4

Бренд: Encore Страницы: 5

Бренд: TAGSYS RFID Страницы: 51

Wi-Fi Inventory Reader

Бренд: TAGSYS RFID Страницы: 36

Media X-Change 2.0

Бренд: Kanguru Страницы: 17

RFU630-041 Series

Бренд: SICK Страницы: 78

Бренд: IDTECK Страницы: 26

Бренд: Elatec Страницы: 50

Бренд: Bafo Страницы: 21

Бренд: Magtek Страницы: 33

Бренд: Shindaiwa Страницы: 20

Бренд: IDTECH Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды