Kugelmann Maschinenbau DUPLEX Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 60

background image

Chapter 06

55

www.kugelmann.com

Exchange of the sensors at the screw conveyors, the spreading disc and the chute

If no feedback arrives at the control, this can have many reasons. The last possibity is that the sensor is defect.

Check the oil supply before and see whether the screw conveyors are blocked.

Loosen attachment and dismount sensor and supply cable. Mount new sensor. Connect supply cable with the
appropriate clamp.

The sensor at the chute is a safety element. As soon as the spreading unit is folded upward the spreading disc
rotation stops.

Replace defective sensors immediately. Danger through rotating tools!
Park vehicle and remove ignition key.

Wear parts

Wear parts are:

the spreading disc

both srew conveyors

the cabin and the sprockets
the bearings of the spreading disc and the

screw conveyors
all light bulbs

all oil and water filters

all hydraulic hoses are to be replaced every six
years
all hoses and sleeves
cover tarpaulins and the outer
valance at the back
all springs,dampers and rubber buffers

Observe all safey regulations when you deal with hydraulic cables, couplings
and parts in chapter 1. Hydraulic cables must not be repaired and are to be replaced immediately.

Subject to changes

English

«
...
53
54
55
56
57
...
»

Содержание DUPLEX





























































Отзывы:

Нет отзывов

Похожие инструкции для DUPLEX

Бренд: xpr Страницы: 10

Бренд: SaMASZ Страницы: 19

Бренд: HID Страницы: 2

Бренд: V.TOP Страницы: 9

Бренд: Datecs Страницы: 18

Бренд: Addonics Technologies Страницы: 1

Бренд: CDVI Страницы: 20

Бренд: Kobil Страницы: 3

Traveldrive 1000&1

Бренд: Hama Страницы: 22

Бренд: TurfEx Страницы: 56

Бренд: Tricubes Страницы: 12

Бренд: Rosslare Страницы: 50

Бренд: Iron Baltic Страницы: 48

Бренд: Manhattan Страницы: 12

Бренд: Omron Страницы: 236

Бренд: xpr Страницы: 4

Бренд: Rauch Страницы: 146

Бренд: CDVI Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды