Kubota WSM L3540-II Скачать руководство пользователя

Страница: 114 / 672

ENGINE

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

1-S12

4. CHECKING AND ADJUSTING

[1] ENGINE BODY

Compression Pressure

1. Run the engine until it is warmed up.
2. Stop the engine and disconnect the

connector from the stop

solenoid in order not to inject fuel.

3. Remove the air cleaner, the muffler and all injection nozzles.
4. Set a compression tester (Code No. 07909-30208) with the

adaptor to the nozzle hole.

5. Keep the engine stop lever at

"Stop Position"

6. While cranking the engine with the starter, measure the

compression pressure.

7. Repeat steps 4 through 6 for each cylinder.
8. If the measurement is below the allowable limit, apply a small

amount of oil to the cylinder wall through the nozzle hole and
measure the compression pressure again.

9. If the compression pressure is still less than the allowable limit,

check the top clearance, valve and cylinder head.

10. If the compression pressure increases after applying oil, check

the cylinder wall and piston rings.

NOTE

• Check the compression pressure with the specified valve

clearance.

• Always use a fully charged battery for performing this test.
• Variances in cylinder compression values should be under

10 %.

9Y1211167ENS0005US0

Compression pressure

Factory specification

3.6 to 4.0 MPa
36 to 41 kgf/cm

520 to 580 psi

Allowable limit

2.5 MPa
26 kgf/cm

370 psi

KiSC issued 02, 2015 A

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание WSM L3540-II

Отзывы:

Похожие инструкции для WSM L3540-II

Бренды по названию

Популярные бренды

Kubota WSM L3540-II, Руководство по ремонту

Результаты поиска

Содержание WSM L3540-II

Отзывы:

Похожие инструкции для WSM L3540-II

Бренды по названию

Популярные бренды