Kubota WSM L3540-II Скачать руководство пользователя страница 289

Страница: 289 / 672

TRANSMISSION

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

3-S43

Clutch Rod, Brake Pedal Rod and Electric Wiring

1. Disconnect the brake pedal rod (6) and clutch rod (4).
2. Disconnect the wiring connectors for alternator (1), coolant

temperature sensor (9), oil pressure switch (2), fuel unit (3),
starter motor (7) and battery (10).

3. Remove the ground cable (11).
4. Remove the wiring harness and A/C hoses (5) together with the

wiring harness stay (12).

NOTE

• The bolt mounting the ground cable (11) is different from

the others.

(When reassembling)

• Be sure to check and adjust the clutch and brake pedal free

travel. (Refer to "7. CHECK AND MAINTENANCE" at "G.
GENERAL" section.)

9Y1211167CLS0009US0

Tightening torque

Alternator

terminal

5.9 to 9.8 N·m
0.6 to 1.0 kgf·m
4.4 to 7.2 lbf·ft

Starter

terminal

7.4 to 9.8 N·m
0.75 to 1.0 kgf·m
5.5 to 7.2 lbf·ft

(1) Alternator
(2) Oil Pressure Switch
(3) Fuel Unit
(4) Clutch Rod
(5) A/C Hose
(6) Brake Pedal Rod

(7) Starter Motor
(8) Clamp
(9) Coolant Temperature Sensor
(10) Battery
(11) Ground Cable
(12) Wiring Harness Stay

KiSC issued 02, 2015 A

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание WSM L3540-II

Отзывы:

Kubota WSM L3540-II, Руководство по ремонту, Страница: 289 / 672

Результаты поиска

Содержание WSM L3540-II

Отзывы: