manualshive.com logo in svg

Kubota WSM L3540-II, Руководство по ремонту, Страница: 279 / 672

Поделиться
Скачать
Kubota WSM L3540-II Скачать руководство пользователя страница 279

TRANSMISSION

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

3-S33

Adjustment of HST Sensor (HST Pedal, Range Shift Lever,
Cruise Lever, HST Response Dial, Fine-adjustment Mode)

NOTE

• When any of ECU, HST pedal sensor, cruise control lever

position sensor, swashplate position sensor, range gear
shift sensor, HST response dial or proportional valve
connector (Forward, Reverse) is replaced, this adjustment
is required.

• Tractor Condition

Parking brake: Set the Apply the Parking Brake Cruise
Control Lever: Set the Neutral Position HST Pedal: Set the
Neutral Position
Range Gear Shift Lever: Set the Neutral Position (between
L and M)
HST Response Dial: Set the Center Detente Position

1. While holding down the both switches at once, start the engine

at idling speed.

2. Select mode 

"K"

.

3. Hold down the display mode switch for more than 2 seconds.
4.

"HST-ADJ" (b)

 is displayed and release the switch.

NOTE

• When indication "HST-ADJ" does not change, the engine is

not idling, or the parking brake is not used.

• When "ERROR-xx" is displayed (k), refer to the below chart.

5.

"PUSH-SW"

 is displayed 

(c)

: Hold down the displayed mode

switch for more than 2 seconds.

(Reference)

(To be continued)

Error Display

Fine-adjustment

ERROR-71

Range Gear Shift Sensor

ERROR-72

HST Pedal Sensor

ERROR-73

Swashplate Position Sensor

ERROR-74

Cruise Control Lever Position Sensor

ERROR-75

Accelerator Lever Sensor

ERROR-76

HST Response Dial

(a) Mode Selection Display
(b) Information Display
(c) Setting Display-1
(d) Adjusting Display-1
(e) Setting Display-2
(f)

Adjusting Display-2

(g) Setting Display-3

(h) Setting Display-4
(i)

Adjusting Display-3

(j)

Correct Preserving Display

(k) Error Display-1
(l)

Error Display-2

(m) Error Display-3

KiSC issued 02, 2015 A 

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов