Kubota WSM L3540-II Скачать руководство пользователя страница 668

Страница: 668 / 672

CABIN

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

10-S50

(6) Cabin Windshields

Preparation

1. Prepare the followings.

• Cutter knife

1 piece

• Scraper

1 piece

• Gun for coating

1 piece

• Sika Tack-Ultrafast or equivalent
• Gummed tape
• Sika-Activator
• Sika primer 209
• Shin Etsu silicon KE420
• Sika-cleaner 205

NOTE

• Sika product are made by Sika Corporation.
• Shin Etsu silicon KE420 is made by Shin Etsu Polymer

Corporation.

• These materials can't be provided by Kubota Corporation.
• Therefore, please find the local made equivalent materials

in your country and use them when you need.

9Y1211167CAS0071US0

Before Replacing Windshields (1)
[In case of using piano wire (When glass is clacked)]

1. Thread the piano wire from the inside of cabin. Tie its both ends

to a wooden blocks or the like. (See the left figure.)

2. Pull the piano wire inward/outward alternately to cut the

adhered part.

NOTE

• Do not let the piano wire make sliding contact with the edge

of glass plate forcibly.

[In case of using cutter knife (When glass is totally crushed
finely)]

1. Insert the knife (3) into the adhered part.
2. Keep the edge of knife blade square to the glass edge at the

part

"a"

. Slide the knife blade along the glass surface and the

edge. Pull the part

"b"

in the direction parallel to the glass edge

to cut them off.

NOTE

• Find a wider gap between the glass and body.
• Be careful of handling the cutter knife not to damage your

hand.

9Y1211167CAS0072US0

Before Replacing Windshields (2)

1. When the Sika Tack-Ultrafast or equivalent attached to the

cabin frame and the glass are reused, remove the bond clearly.

2. Clean the frame surface with Sika-Activator.

NOTE

• Remove the bond completely.

9Y1211167CAS0073US0

(1) Piano Wire
(2) Wood Peace

(3) Cutter Knife
(4) Pulling

KiSC issued 02, 2015 A

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание WSM L3540-II

Отзывы:

Kubota WSM L3540-II, Руководство по ремонту, Страница: 668 / 672

Результаты поиска

Содержание WSM L3540-II

Отзывы: