manualshive.com logo in svg

Kubota WSM L3540-II, Руководство по ремонту, Страница: 221 / 672

Поделиться
Скачать
Kubota WSM L3540-II Скачать руководство пользователя страница 221

TRANSMISSION

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

3-M21

[C] GST Clutch

The GST clutch is hydraulic multiple plate type and

is provided between the counter shaft (3) and the shuttle
shaft (8), and it 

"engages"

 and 

"disengages"

 the

power from the engine. This is controlled by the
operation of clutch valve (2).

Engaging (When the shift gear is at desired
position while engine is running)

The oil from clutch valve (2) flows in to push the

return spring (9) and the piston (6). The piston is pushed
to the left by the oil, thereby pushing the clutch discs (4)
and the plates (5) to transmit the power.

Disengaging (When the engine stop, the shift
levers are neutral position, between from start to
end of the gear shifting)

The oil of the GST clutch (1) is pushed out with return

spring (9) and piston (6), and flowed to the tank.

9Y1211167TRM0029US0

[5]  FRONT WHEEL DRIVE SECTION

Refer to the "2. MANUAL TRANSMISSION MODEL" in this section for the front wheel drive section of GST model.

9Y1211167TRM0030US0

[6] CREEP GEAR SECTION

Refer to the "2. MANUAL TRANSMISSION MODEL" in this section for the creep gear section of GST model.

9Y1211167TRM0031US0

[7]  SHIFT LINKAGE MECHANISM

Refer to the "2. MANUAL TRANSMISSION MODEL" in this section shift linkage mechanisms of "Shuttle Lever"

and "Front Wheel Drive Lever".

9Y1211167TRM0032US0

(1) GST Clutch
(2) Clutch Valve
(3) Counter Shaft
(4) Clutch Disc
(5) Plate
(6) Piston

(7) Clutch Case
(8) Shuttle Shaft
(9) Return Spring
(10) Clutch Output Hub
(11) Clutch Input Hub

KiSC issued 02, 2015 A 

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов