Kubota WSM L3540-II Скачать руководство пользователя страница 427 | Manualshive

Страница: 427 / 672

Kubota WSM L3540-II Скачать руководство пользователя страница 427

STEERING

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

7-M2

2. HYDRAULIC CIRCUIT

When the engine starts, the hydraulic pump (8)

pressure-feeds the oil, drawn from the transmission case
(7) through the oil filter (6), to the steering controller (3).

The oil which has entered steering controller (3) is

directed to control valve (10).

As the steering wheel is turned, control valve (10)

operates and the oil passes through gerotor (1) and into
steering cylinder (2). The cylinder rod then moves to
control the directional movement of the front wheels.

Return oil from steering cylinder (2) passes through

control valve (10) is sent to the PTO clutch valve, HST,
GST valve, etc..

When the engine is not operating, and the steering

wheel is turned, gerotor (1) rotates to supply oil to
steering cylinder (2). Thus the machine can be steered
manually.

9Y1211167STM0002US0

(1) Gerotor
(2) Steering Cylinder
(3) Steering Controller
(4) Relief Valve
(5) Check Valve
(6) Oil Filter
(7) Transmission Case
(8) Hydraulic Pump

(9) Steering Wheel
(10) Control Valve

A: To Three Point Hydraulic

System and Others

B: To PTO Clutch Valve, HST,

GST Valve, etc.

KiSC issued 02, 2015 A

«
...
425
426
427
428
429
...
»

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов