ENGINE
L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM
1-S13
Valve Clearance
IMPORTANT
• Valve clearance must be checked and adjusted when
engine is cold.
1. Remove the head cover, the glow plugs and the timing window
cover on the clutch housing.
2. Align the
"1TC"
mark line (1) on the flywheel and center of
timing window (2) so that the No. 1 piston comes to the
compression or overlap top dead center.
3. Check the following valve clearance marked with "
" using a
feeler gauge.
4. If the clearance is not within the factory specifications, adjust the
valve clearance with the adjusting screw.
NOTE
• The "1TC" mark line (1) on the flywheel is just for No. 1
cylinder. There is no "TC" marking for the other cylinders.
• No. 1 piston comes to the T.D.C. position when the "1TC"
mark line is aligned with center of timing window on
clutch-housing. Turn the flywheel 0.26 rad (15 °) clockwise
and counterclockwise to see if the piston is at the
compression top dead center or the overlap position. Now
referring to the table below, readjust the valve clearance
"A". (The piston is at the compression top dead center
when both the IN. and EX. valves do not move; it is at the
overlap position when both the valves move.)
• Finally turn the flywheel 6.28 rad (360 °) and align the "1TC"
mark line (1) and the center of timing window (2). Adjust all
the other valve clearance as required.
• After turning the flywheel counterclockwise twice or three
times, recheck the valve clearance "A", firmly tighten the
lock nut of the adjusting screw.
9Y1211167ENS0006US0
Valve clearance
Factory specification
0.18 to 0.22 mm
0.0071 to 0.0087 in.
Adjustable cylinder location
of piston
Valve arrangement
D1803-M
V2203-M
V2403-M-T
IN.
EX.
IN.
EX.
When No. 1 piston
comes to
compression top
dead center
No. 1
No. 2
No. 3
No. 4
–
–
When No. 1 piston
comes to overlap
position
No. 1
No. 2
No. 3
No. 4
–
–
(1)
"1TC"
Mark Line
(2) Timing Window
(3) Timing Mark
A: Valve Clearance
KiSC issued 02, 2015 A
Содержание WSM L3540-II
