Kubota WSM L3540-II Скачать руководство пользователя страница 638

Страница: 638 / 672

CABIN

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

10-S20

Charging an Empty or Partially Charged System (Vapor)

This procedure is to charge the system through the

pressure

side with refrigerant in the vapor state. When the refrigerant
container is set right side up, refrigerant will enter the system as a
vapor.

CAUTION

• Never open the HI pressure side valve of manifold gauge

while the engine is running.
NOTE

• Do not turn the refrigerant container upside-down when

charging the system by running the engine.

• Put refrigerant container into a pan of warm water

(maximum temperature 40 °C (104 °F)) to keep the vapor
pressure in the container slightly higher than vapor
pressure in the system.

1. Check that the

pressure side valve (4) is closed.

2. Start the engine and set an approx.

1500 min

-1

(rpm)

3. Turn on the A/C switch.

Set the temperature control lever to

maximum cooling

position

and the blower switch to

position.

4. Open the

pressure side valve (5) of manifold gauge and the

can tap valve (3) on refrigerant container and charge the
refrigerant until air bubbles in the sight glass of the receiver
vanish.

5. After charging the specified amount of refrigerant into the

system, close the

pressure side valve (5) of manifold gauge

and can tap valve (3), then stop the engine.

6. Check for gas leak with an electric gas leak tester. (Refer to "(4)

Electric Gas Leak Tester" in this section.)

(Reference)

• Specified amount of refrigerant (total)

770 to 870 g (1.70 to 1.90 lbs) [Refrigerant R134a]

• Manifold gauge indication at fully charged system (at ambient

temperature: 30 °C (86 °F))

pressure side

1.27 to 1.66 MPa (13 to 17 kgf/cm

, 185 to 242 psi)

pressure side

0.15 to 0.20 MPa (1.5 to 2.0 kgf/cm

, 21 to 28 psi)

9Y1211167CAS0031US0

(1)

Pressure Gauge

(2)

Pressure Gauge

(3) Can Tap Valve

(4)

Pressure Side Valve

(5)

Pressure Side Valve

KiSC issued 02, 2015 A

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание WSM L3540-II

Отзывы:

Kubota WSM L3540-II, Руководство по ремонту, Страница: 638 / 672

Результаты поиска

Содержание WSM L3540-II

Отзывы: