Kubota WSM L3540-II Скачать руководство пользователя | Manualshive

Страница: 287 / 672

background image

TRANSMISSION

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

3-S41

Draining Coolant

WARNING

• Do not remove the radiator cap when the engine is hot.

Then loosen cap slightly to the stop to relieve any excess
pressure before removing cap completely.

1. Stop the engine and let cool down.
2. To drain the coolant, open the radiator drain plug (3) and

remove the radiator cap (1). The radiator cap (1) must be
removed to completely drain the coolant.

3. After all coolant is drained, close the drain plug (3).

(When refilling)

• Fill with clean water and anti-freeze until the coolant level is just

below the port. Install the radiator cap (1) securely.

• Fill with coolant up to

"FULL"

mark on the recovery tank.

• Start and operate the engine for few minutes.
• Stop the engine and let cool. Check coolant level of recovery

tank (2) and add coolant if necessary.

NOTE

• On cabin model machines, fresh water circulates through

the heater. This means that one more liter or so of fresh
water is required.
In changing fresh water, pour fresh water up to the filter
port of the recovery tank. Turn "ON" the heater (shift the
temperature control lever toward WARM), and run the
engine for a while in order to warm fresh water. Then stop
the engine.
When fresh water has cooled down, some of the fresh
water in the recovery tank is sucked. Now the recovery tank
is appropriately filled with fresh water.

IMPORTANT

• Do not start engine without coolant.
• Use clean, fresh water and anti-freeze to fill the radiator and

recovery tank.

• When the anti-freeze is mixed with water, the anti-freeze

mixing ratio must be less than 50 %.

• Securely tighten radiator cap. If the cap is loose or

improperly fitted, water may leak out and the engine could
overheat.

• Refer to "4. LUBRICANTS, FUEL AND COOLANT" on page

9Y1211167CLS0006US0

Coolant
(with recovery tank)

Capacity

L3540-II,
L4240-II

8.5 L
9.0 U.S.qts
7.5 Imp.qts

L5040-II,
L5240-II,
L5740-II

9.2 L
9.7 U.S.qts
8.1 Imp.qts

(1) Radiator Cap
(2) Recovery Tank
(3) Drain Plug

(A) FULL
(B) LOW

KiSC issued 02, 2015 A

«
...
285
286
287
288
289
...
»

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WSM L3540-II

Бренд: FENDT Страницы: 267

Бренд: Agria Страницы: 76

Бренд: Pkm Страницы: 34

Бренд: Cub Cadet Страницы: 52

Groom Master II 88009

Бренд: Jacobsen Страницы: 104

Бренд: Jenn-Air Страницы: 28

Бренд: LSM Страницы: 44

Бренд: Toro Страницы: 2

Бренд: Toro Страницы: 64

Бренд: PÖTTINGER Страницы: 14

SYNKRO 4003 K+T

Бренд: Pottinger Страницы: 31

Single Row Walking Tractor

Бренд: Knapik Страницы: 34

Бренд: Cub Cadet Страницы: 32

Бренд: Cub Cadet Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды