Kubota WSM L3540-II Скачать руководство пользователя страница 559

Страница: 559 / 672

ELECTRICAL SYSTEM

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

9-S26

(6) Mode "E" (GST Lever Sensor Fine-adjustment Mode) Setting the GST

Lever's Neutral Position with its Sensor

IMPORTANT

• As for this fine-adjustment, be sure to set it correctly

because the set state becomes the standard of the control
thereafter.
NOTE

• When the GST lever sensor, the ECU or the electronic

instrument panel is replaced, this adjustment is required.

1. Set the GST shift lever to

Neutral

position.

2. While holding down the both switches at once, turn on the main

switch.

3. Select the mode

"E"

"LEVER"

is displayed

(b)

and

"PUSH SW"

is displayed

(c)

for

five seconds.

5. Hold down the display mode switch for more than 2 seconds.

(This preserve the adjusted value to the ECU.)

"OK"

is displayed

(d)

on LCD screen to tell that preserving to

ECU has been made correctly. Turn off the main switch to end
the mode.

7. If

"NG"

is displayed

(f)

, it means the preserving has not been

made correctly (4). Turn off the main switch and repeat the
procedure.

8. If

"LEVER"

is displayed

(b)

first and then

"ERROR-70"

shows

(e)

, it means the lever sensor voltage is out of specification.

In this case;

• Check to see that GST lever is at the

Neutral

position.

• Check the lever sensor voltage in the Test Mode (Mode

"A"

). If out of specification, replace the sensor itself.

9Y1211167ELS0021US0

(1) Liquid Crystal Display (LCD)
(2) Display Mode Switch
(3) Travel Speed Switch

(a) Mode Selection Display
(b) Information Display
(c) Adjusting Display
(d) Correct Preserving Display
(e) Error Display
(f)

Incorrect Preserving Display

KiSC issued 02, 2015 A

Содержание WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание WSM L3540-II

Отзывы:

Kubota WSM L3540-II, Руководство по ремонту, Страница: 559 / 672

Результаты поиска

Содержание WSM L3540-II

Отзывы: