background image

This operator’s manual contains handling tips and precautions for safe operation of your 

BAD BOY 1025H  

tractor. Read it carefully before you operate your tractor and make sure that you have a full understanding of 

this manual. This will ensure correct operation and to keep the tractor optimum condition.

After reading the manual, keep it close to the tractor for immediate reference. When you loan your tractor to 

someone else, loan the manual as well.

In case the manual is lost or damaged, please contact your local authorized dealer for a copy. Some parts of 

this product may have been changed for the improvement of quality or for safety reasons, in which case the 

photographs or drawings of the parts in this booklet may not be the same as the actual parts installed on this 

product. If you fi nd anything in this manual unclear or need further explanation, please contact your autho-

rized dealer.

PREFACE

 Regarding the purpose of this machine

  Do not modify the machine or try to do the job which is beyond purpose of this machine. Otherwise it may cause the 

warranty cancellation. (Refer to warranty statement for detail)

1025H.indb   1

1025H.indb   1

2021-07-06   오전 11:07:30

2021-07-06   오전 11:07:30

Summary of Contents for 1025H

















































































































































Reviews: