Korg TRITON Le, Руководство по параметрам

Страница: 14 / 269

PROG
1.1
2.1
2.2
3.1
4.1
4.2
5.1
5.2
5.3
6.1
7.1
7.2
PROG
1.1
2.1
2.2
3.1
4.1
4.2
5.1
5.2
5.3
6.1
7.1
7.2
7
Each multisample has an upper limit, and may not pro-
duce sound when played above that limit.
S.Ofs (High Start Offset) [Off, On]
This specifies the point at which the multisample will begin
sounding. For some multisamples this parameter will have
no effect.
On (checked): The sound will start from the start offset
location that is pre-determined for each multisample.
However when a RAM bank is selected, this will depend on
the selected multisample. If you select a multisample that
includes one of the following types of sample, checking this
item will cause playback to start from the Loop Start
Address.
• A sample that was recorded (sampled) in Sampling
mode (if the separately sold EXB-SMPL option is
installed)
• A sample whose Loop Start Address was edited in
Sampling mode (if the EXB-SMPL option is installed)
after the sample was loaded in Media mode
• A sample whose Loop Start Address was specified
automatically when it was loaded as an AKAI, AIFF, or
WAVE file in Media mode
Off (unchecked): The sound will start from the beginning of
the multisample waveform.
Rev (High Reverse) [Off, On]
The multisample will be played in reverse. In the case of
ROM multisamples that were originally specified to loop, or
in the case of RAM multisamples that were set to loop in
Sampling mode (if the EXB-SMPL option is installed), the
multisample will be played back in “one-shot” reverse
mode. If the multisample was originally set to reverse, it will
playback without change.
On (checked): The multisample will playback in reverse.
Off (unchecked): The multisample will playback normally.
Level (High Level) [000...127]
Specifies the level of the multisample.
Depending on the multisample, high settings of this
parameter may cause the sound to distort when a chord
is played. If this occurs, lower the level.
Low:
Specifies the OSC1 Low multisample.
The Low multisample will sound when the velocity is less
than the “Velocity SW L
→
H” (2.1–2a) setting.
Low MS Bank [ROM, RAM]
Low Multisample [000...424, 000...999]
S.Ofs (Low Start Offset) [Off, On]
Rev (Low Reverse) [Off, On]
Level (Low Level) [000...127]
☞
Refer to the corresponding item in “High.”
2.1–2c: Octave, Transpose, Tune, Delay
Octave [–2[32’], –1[16’], +0[8’], +1[4’]]
Adjusts the pitch in octave units. The normal octave of the
multisample is 8' (feet).
Transpose [–12…+12]
Adjusts the pitch in semitone steps over a range of ±1
octave.
Tune [–1200…+1200]
Adjusts the pitch of the sample in one-cent steps (a semitone
is 100 cents) over a range of ±1 octave.
Delay [0ms…5000ms, KeyOff]
Specifies a delay time from note-on until the note will
sound.
With a setting of KeyOff, the sound will begin when note-
off occurs. This is used to create sounds such as the “click”
that is heard when a harpsichord note is released. In this
case, set the “Amp1 EG”, “Amp2 EG” (5.1–3a, 5.2–3) “S
(Sustain Level)” parameter to 0.
2.1–2d: OSC1 Drum Kit
Drum Kit [00(INT)...15(INT), 16(User)...23(User),
24(GM)...32(GM)]
Select a drum kit.
Octave [–2[32’], –1[16’], +0[8’], +1[4’]]
Adjusts the pitch in octave units. When using a drum kit, set
the Octave to 8'.
When editing a drum program, you must set this
parameter to 8'. With other settings, the sounds of the
drum kit will be assigned to the wrong notes of the key-
board.
Transpose [–12…+12]
This adjusts the location of the instruments in the selected
drum kit. Unless you need to change this, leave it at 0.
Tune [–1200…+1200]
This adjusts the pitch in one-cent units.
The pitch of each drum kit can be adjusted in GLOBAL 5.1:
DKit.
Delay [0ms…5000ms, KeyOff]
This specifies a delay time from note-on until the sound will
begin.
With a setting of KeyOff, the sound will begin when note-
off occurs. In this case, set the “Amp1 EG” parameter “S
(Sustain Level)” (5.1–3a) to 0.
■
2.1–2e. UTILITY
☞
“Write Program” (1.1–1c), “Copy Oscillator,” “Swap
Oscillator” (2.1–1d)
For details on how to select the desired utility function, refer
to “PROG 1.1–1c: UTILITY.”
Select by Category
Selects multisamples by category.
00 (INT)–15 (INT) Preload drum kits.
16 (User)–23 (User) for user drum kits
24 (GM)–32 (GM) ROM preset drum kits compatible with GM2.