manualshive.com logo in svg

Komatsu D51EX-24, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu D51EX-24 Скачать руководство пользователя страница 17

CONTROL LEVERS AND PEDALS ................................................................................................. 3-87
OTHER EQUIPMENT ...................................................................................................................... 3-92

MACHINE OPERATIONS AND CONTROLS ........................................................................................ 3-120

CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE ...................................................... 3-120
METHOD FOR STARTING ENGINE.............................................................................................. 3-151
METHOD FOR OPERATIONS AND CHECKS AFTER STARTING ENGINE ................................. 3-156
METHOD FOR STOPPING ENGINE ............................................................................................. 3-159
METHOD  FOR  STARTING  MACHINE  (TRAVEL  FORWARD  AND  REVERSE)  AND  STOPPING  MA-

CHINE ........................................................................................................................................ 3-161

SHIFT GEARS ............................................................................................................................... 3-164
METHOD FOR SWITCHING BETWEEN FORWARD AND REVERSE .......................................... 3-167
METHOD FOR STEERING MACHINE........................................................................................... 3-168
RECOMMENDED WORKING MODES FOR WORKS ................................................................... 3-171
PRECAUTIONS FOR OPERATION ............................................................................................... 3-173
PRECAUTIONS WHEN OPERATING ON SLOPE......................................................................... 3-174
DO NOT OPEN DOOR WHILE OPERATING MACHINE ............................................................... 3-175
DO NOT MODIFY CAB GLASS IN ANY WAY THAT WILL OBSTRUCT THE VIEW ...................... 3-175
PRECAUTIONS FOR FLOATING OPERATION............................................................................. 3-175
PRECAUTIONS FOR BLIND SPOTS CAUSED BY CAB AND ROPS STRUCTURES .................. 3-175
RECOMMENDED APPLICATIONS................................................................................................ 3-175
METHOD FOR ADJUSTING WORK EQUIPMENT ........................................................................ 3-177
TIPS FOR LONGER UNDERCARRIAGE LIFE .............................................................................. 3-178
METHOD FOR PARKING MACHINE ............................................................................................. 3-181
METHOD FOR CHECKING AFTER FINISHING WORK................................................................ 3-183
LOCK............................................................................................................................................. 3-183

HANDLE AIR CONDITIONER............................................................................................................... 3-188

EXPLANATION OF AIR CONDITIONER EQUIPMENT.................................................................. 3-188
METHOD FOR OPERATING TO PREVENT DUST FROM ENTERING INTO CAB ....................... 3-189
METHOD FOR CHECKING DURING OFF SEASON..................................................................... 3-189
METHOD FOR REPLACING RECEIVER ...................................................................................... 3-190

HANDLE RADIO ................................................................................................................................... 3-191

EXPLANATION OF RADIO EQUIPMENT ...................................................................................... 3-191
METHOD FOR CONTROLLING RADIO ........................................................................................ 3-193
ANTENNA...................................................................................................................................... 3-195

TRANSPORTATION.............................................................................................................................. 3-196

TRAVEL ON ROAD........................................................................................................................ 3-196
PRECAUTIONS FOR TRANSPORTING MACHINE ...................................................................... 3-196
TRANSPORTATION PROCEDURE ............................................................................................... 3-196
REMOVE CAB ............................................................................................................................... 3-196
METHOD FOR REMOVING WORK EQUIPMENT......................................................................... 3-196
LOADING AND UNLOADING WITH TRAILER .............................................................................. 3-197
METHOD FOR LIFTING MACHINE ............................................................................................... 3-201

COLD WEATHER OPERATION............................................................................................................ 3-203

COLD WEATHER OPERATION INFORMATION ........................................................................... 3-203
PRECAUTIONS AFTER DAILY WORK COMPLETION ................................................................. 3-204
AFTER COLD WEATHER SEASON .............................................................................................. 3-204

PRECAUTIONS FOR LONG-TERM STORAGE ................................................................................... 3-206

PREPARATION FOR LONG-TERM STORAGE ............................................................................. 3-206
MAINTENANCE DURING LONG-TERM STORAGE...................................................................... 3-206
STARTING MACHINE AFTER LONG-TERM STORAGE............................................................... 3-206

TROUBLES AND ACTIONS ................................................................................................................. 3-208

PRECAUTIONS FOR TOWING MACHINE .................................................................................... 3-208
PRECAUTIONS FOR DISCHARGED BATTERY ........................................................................... 3-209
OTHER TROUBLE......................................................................................................................... 3-215

MAINTENANCE............................................................................................................................................... 4-1

PRECAUTIONS FOR MAINTENANCE ..................................................................................................... 4-2

CHECK SERVICE METER READING ............................................................................................... 4-2
KOMATSU GENUINE REPLACEMENT PARTS ................................................................................ 4-2

FOREWORD

TABLE OF CONTENTS

1-15

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды