Komatsu D51EX-24 Скачать руководство пользователя страница 308 | Manualshive

Страница: 308 / 382

Komatsu D51EX-24 Скачать руководство пользователя страница 308

2.

Pull the radiator grille backward and raise it upward.
Open the radiator grille to the fully opened position, check
that it is locked, and then release your hand.

3.

Remove mud, dirt, leaves, etc. in the radiator fins.
Blow off the heavy clogging with the compressed air.
Steam or water may be used instead of compressed air.

4.

Check the rubber hoses. If any hose is cracked or be-
comes brittle, replace it with a new one. Also check all the
hose clamps for looseness.

5.

Close the radiator grille according to the following proce-
dure.
1) Lift up the radiator grille, and push lock releasing bar

(2) to the direction of arrow.
The lock is released.

2) Close the radiator grille.

6.

Tighten the bolts (1) (2 pieces) on the lower part of the ra-
diator grille.

REMARK

• For opening and closing the radiator grille, see “METHOD FOR OPENING AND CLOSING RADIATOR

GRILLE”.

• For opening and closing the radiator grille of the machine equipped with ripper, see ATTACHMENTS AND

OPTIONS, “METHOD FOR OPENING AND CLOSING RADIATOR GRILLE”.

METHOD FOR CLEANING HYDRAULIC TANK BREATHER

At the check and maintenance, if the breather is dirty, clean it.
1.

Remove nut (2) of breather assembly (1) on the top of the
hydraulic tank.
Use a tool when the nuts are so tight to remove.

2.

Remove cover (3).

3.

Remove dirt sticking to breather element (4).

4.

Clean in clean diesel fuel or flushing oil.

5.

Install cover (3) and nut (2).
In order not to damage the threaded portion of nut, tighten
nut (2) by hand until it is seated. Then tighten it 15 to 30 °
by using a tool.

METHOD FOR CLEANING FUEL TANK BREATHER

At the check and maintenance, if the breather is dirty, clean it.

MAINTENANCE PROCEDURE

MAINTENANCE

4-32

«
...
306
307
308
309
310
...
»

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды