manualshive.com logo in svg

Komatsu D51EX-24, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu D51EX-24 Скачать руководство пользователя страница 344

NOTICE

• Komatsu recommends using Komatsu genuine parts for replacement parts.
• If the engine is operated without the filter element, the turbocharger and aftercooler become dirty

and their performance will lower and that can cause engine problems such as overrun caused by
suction of oil. Therefore, do not start the engine without the filter element.

• The filter element cannot be cleaned. Flushing or regenerating of the filter element will degrade the

performance  of  the  filter.  As  a  result,  the  turbocharger  and  aftercooler  become  dirty  and  the  per-
formance  lowers  or  the  crankcase  pressure  increases.  Never  reuse  the  filter  element  since  it  can
cause an engine failure.

• After the filter element is replaced, if KCCV is not assembled correctly, oil or blowby gas may leak.

Replace the filter element in the correct procedure.

• Always stop the engine and clean around the KCCV before replacing the element.

Prepare the special wrench for KCCV and a container to receive the oil.
1.

Remove the engine side cover (1) on the right side of the
machine.

The KCCV ventilator is located in the position shown in the
figure.

For the use of the special wrench, see the figure.

MAINTENANCE PROCEDURE

MAINTENANCE

4-68

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды