manualshive.com logo in svg

Komatsu D51EX-24, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu D51EX-24 Скачать руководство пользователя страница 314

6.

Replace the belt with a new one if the belt is stretched and has no allowance for adjustment, or has slipping
sound or squeak because of cuts or cracks of the belt.
Ask your Komatsu distributor for replacement of the belt.
When it has been replaced with a new part, there will be initial elongation. After 2 or 3 days of operation,
adjust it again.

7.

Install the cover (2).

METHOD FOR CHECKING LEVEL OF REFRIGERANT (GAS)

k

k

 WARNING

• Be sure to handle the refrigerant (gas) according to the local regulations.
• If the refrigerant used in the air conditioner gets into your eyes or is splashed on your hands, it may

cause loss of sight or frostbite. Never touch the refrigerant. Do not loosen any part of the refrigerant
circuit.

• Do not bring any open flame close to any point where the refrigerant gas is leaking.

 

The  sight  glass  (inspection  window)  is  located  on  the  pillar  at
the rear left of the machine.
Check  the  refrigerant  gas  (Hydrofluorocarbons  HFC  -134a)
condition with the sight glass (inspection window) of the receiv-
er while the air conditioner is in operation.

(A) Blue: The air conditioner is operated normally.
(B) Pink: The receiver drier needs to be replaced.
If the sight glass (inspection window) is pink, contact your Ko-
matsu distributor for repair.

REMARK

The bubbles or condensation may be generated in the sight glass (inspection window), however, it does not in-
dicate that the refrigerant level is low. It is normal when Hydrofluorocarbons HFC -134a is used. Do not add the
refrigerant gas.

METHOD FOR CHECKING DURING OFF SEASON

Even during the off-season, operate the air conditioner for 3 to 5 minutes once a month to maintain the oil film at
all parts of the compressor.

METHOD FOR BLEEDING AIR FROM HYDRAULIC CIRCUIT

Bleed air from the circuit after the filter element or strainer, etc. has been replaced or cleaned.
Since the engine must be started and the blade must be operated, see OPERATION.
1.

Bleed air from the pump according to the following procedure.

MAINTENANCE PROCEDURE

MAINTENANCE

4-38

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды