manualshive.com logo in svg

Komatsu D51EX-24, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu D51EX-24 Скачать руководство пользователя страница 289

METHOD FOR REPLACING DEF TANK BREATHER ELEMENT........................................................... 4-59
CHECK AND REPLACE ALTERNATOR DRIVE BELT TENSION AND REPLACING ALTERNATOR BELT....

............................................................................................................................................................ 4-59

METHOD FOR CHECKING FOR LOOSE ROPS MOUNT BOLTS ......................................................... 4-60
METHOD FOR CHECKING AND CLEANING FAN ................................................................................. 4-60

EVERY 2000 HOURS MAINTENANCE ......................................................................................................... 4-61

METHOD  FOR  CHANGING  OIL  IN  HYDRAULIC  TANK,  REPLACING  HYDRAULIC  OIL  FILTER  CAR-

TRIDGE, REPLACING HST OIL FILTER CARTRIDGE, AND CLEANING HYDRAULIC TANK STRAINER

............................................................................................................................................................ 4-62

METHOD  FOR  CHECKING  AND  RELEASING  NITROGEN  GAS  CHARGE  PRESSURE  IN  ACCUMULA-

TOR (FOR CONTROL CIRCUIT) ........................................................................................................ 4-65

METHOD FOR CHECKING ALTERNATOR ............................................................................................ 4-67
METHOD FOR CHECKING AND ADJUSTING ENGINE VALVE CLEARANCE ...................................... 4-67
METHOD FOR CHECKING VIBRATION DAMPER ................................................................................ 4-67
METHOD FOR REPLACING KCCV FILTER ELEMENT ......................................................................... 4-67
METHOD FOR REPLACING DEF FILTER.............................................................................................. 4-70

EVERY 4000 HOURS MAINTENANCE ......................................................................................................... 4-73

REPLACE DEFINED LIFE PARTS.......................................................................................................... 4-73
METHOD FOR CHECKING WATER PUMP............................................................................................ 4-73
METHOD FOR CHECKING STARTING MOTOR.................................................................................... 4-74
METHOD FOR REPLACING ACCUMULATOR (FOR CONTROL CIRCUIT) .......................................... 4-74
METHOD  FOR  CHECKING  FOR  LOOSENESS  OF  ENGINE  HIGH-PRESSURE  PIPING  CLAMP,  HARD-

ENING OF RUBBER ........................................................................................................................... 4-74

METHOD FOR CHECKING FOR MISSING FUEL SPRAY PREVENTION CAP, HARDENING OF RUBBER.

............................................................................................................................................................ 4-75

EVERY 4500 HOURS MAINTENANCE ......................................................................................................... 4-75

METHOD FOR CLEANING DEF TANK................................................................................................... 4-76
METHOD FOR CLEANING DEF TANK MOUNTING PORTION ............................................................. 4-76

EVERY 8000 HOURS MAINTENANCE ......................................................................................................... 4-76

METHOD FOR REPLACING FUEL SPRAY PREVENTION CAP............................................................ 4-76

EVERY 9000 HOURS MAINTENANCE ......................................................................................................... 4-76

METHOD FOR REPLACING DEF HOSE ............................................................................................... 4-76
END OF SERVICE LIFE ......................................................................................................................... 4-76

MAINTENANCE INTERVAL WHEN DIESEL FUEL MIXED WITH BIO-FUEL IS
USED

If the diesel fuel which does not include the bio-fuel is changed to the diesel fuel mixed with bio-fuel, set the
maintenance interval as follows.

Replace the fuel prefilter cartridge

When the machine is operated first 250 hours after the diesel fuel has been changed to the diesel fuel mixed
with bio-fuel, and when the machine is operated further 250 hours.
After that, replace it within 500 hours as a periodic replacement by the service meter reading.

Replace the fuel main filter cartridge

When the machine is operated first 250 hours after the diesel fuel has been changed to the diesel fuel mixed
with bio-fuel, and when the machine is operated further 250 hours.
After that, replace it within 1000 hours as a periodic replacement by the service meter reading.

Maintenance interval after the diesel fuel has been changed to the diesel fuel mixed with bio-fuel

Operating hours of the machine

Service meter

When

changed

250 hours

after chang-

ing

500 hours

after chang-

ing

Every 500 hours

Every 1000 hours

Within 500

operating

hours after

changing

After 500 op-
erating hours

after chang-

ing

Within 500

operating

hours after

changing

After 500 op-
erating hours

after chang-

ing

MAINTENANCE

MAINTENANCE SCHEDULE TABLE

4-13

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды