manualshive.com logo in svg

Komatsu D51EX-24, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu D51EX-24 Скачать руководство пользователя страница 238

2.

Set joystick (steering, directional and gear shift lever) (2) to
N (NEUTRAL) position.
Position (A): FORWARD
Position (B): REVERSE
To keep the machine stopped further, depress decelerator/
brake pedal (1) until depressing effort becomes large.

3.

Set parking brake lever (3) to LOCK position (L).

4.

Set blade control lever (4) to LOWER position (C) and low-
er the blade to the ground.

5.

Return blade control lever (4) to HOLD position (B).

6.

Set work equipment lock lever (5) to LOCK position (L).

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-182

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды