manualshive.com logo in svg

Komatsu D51EX-24, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu D51EX-24 Скачать руководство пользователя страница 273

Problem

Main causes

Remedy

Even if the joystick (steering, direc-
tional and gear shift lever) is operat-
ed, machine does not move off.

Parking lever is in LOCK position.

Set to FREE.

Charge pump is worn or scuffed.

Check, replace. (*)

Brake release solenoid does not op-
erate.

Check, repair, replace. (*)

Defective joystick (steering, direction-
al and gear shift lever)

Check, replace. (*)

Fan is set in reverse mode.

Set it to normal rotation mode.

Turbo protect function in operation

Wait until operation finishes.

Only one side of track shoe moves.

HST pump is defective.

Check, replace. (*)

Electrical system is defective.

Check, repair, replace. (*)

Machine deviates without steering
operation.

Defective joystick (steering, direction-
al and gear shift lever)

Adjust, check, repair. (*)

Defective HST pump and motor

Adjust, check, repair, replace. (*)

Defective motor speed sensor

Adjust, check, replace. (*)

Hydraulic oil temperature is low.

Warm-up.

Air is mixed in hydraulic circuit.

Bleed air. (*)

Hydraulic oil gets overheat. (Pointer
is in red range.)

Work load is too large.

Lighten the work load to prevent trav-
el relief.

Work equipment is relieved.

Avoid operating the blade to the
stroke end of cylinder.

Continuous high-speed travel

Drive in lower speed range.

Clogged oil cooler fins or damaged
fin

Clean or repair. See WHEN RE-
QUIRED.

PHENOMENA AND ACTIONS FOR ENGINE RELATED PARTS

• Contact your Komatsu distributor for the remedies indicated with (*) in the remedy column.
• Ask your Komatsu distributor for repairs for problems or causes which are not listed below.

Problem

Main causes

Remedy

After warming up, when engine
speed is increased, engine oil pres-
sure caution lamp still lights up.

Insufficient oil in engine oil pan (suck-
ing in air)

Add oil to specified level. See
CHECKS BEFORE STARTING.

Improper oil is used. (Viscosity is im-
proper.)

Referring to “RECOMMENDED
FUEL, COOLANT, AND LUBRI-
CANT”, replace oil with proper one.

Clogged oil filter cartridge

Replace. See EVERY 500 HOURS
MAINTENANCE.

Oil leakage due to defective tighten-
ing or breakage of oil pipe or pipe
joint.

Check and repair. (*)

Defective monitor

Replace. (*)

OPERATION

TROUBLES AND ACTIONS

3-217

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды