Komatsu D51EX-24 Скачать руководство пользователя страница 248 | Manualshive

Страница: 248 / 382

Komatsu D51EX-24 Скачать руководство пользователя страница 248

DISPLAY SELECTOR BUTTON

Use the display selector button to change frequency and clock shown on the display.
Each time you press this button, frequency, clock and band are shown on the display in this order.
If 1.5 seconds passes while a band is shown, a frequency will be displayed.
As long as AUX is selected, this button alternately switches the display between AUX and the clock.

SOUND CONTROL BUTTON

Press the sound control button, and the sound adjustment is ready.
Each time this button is pressed, BAL (Balance), TRE (Treble) and BAS (Bass) will be selected in this order.
If this button is pressed while BAS is displayed, the sound adjustment will be canceled.

DISPLAY

(A): Band name, “AUX”, frequency, clock and other character/

numeric information are displayed.

(B): Frequencies are displayed at steps of 50 kHz in certain
areas.
(C): Lights up when a stereo broadcasting is heard while a FM

station is selected.

(D): Lights up at the time of balance adjustment in the sound

adjusting condition.

(E): Lights up at the time of treble adjustment in the sound ad-

justing condition.

(F): Lights up at the time of bass adjustment in the sound adjusting condition.

AUX

NOTICE

• A stereo miniature plug can be connected.

Read the instruction manual of the equipment to connect carefully.

• As a power source for the equipment to connect, use the battery attached to that equipment.

If you use an electric power supply installed to the machine, the noise may occur.

• The noise may occur if you pull out the input plug when AUX is selected, or if you push in or pull

out the plugs of the equipment to connect.

You can hear the sound through the speaker of the machine when you connect a commercially available porta-
ble audio equipment to the machine.

HANDLE RADIO

OPERATION

3-192

«
...
246
247
248
249
250
...
»

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды